Every Rotisserie component we have

ROTISSERIE SHIELD BRACKET FOR RIGHT SIDE WITH TWO MOUNTING HOLES. (Also, a replacement for 10184-E43.)

Part Number: 10184-E33
Weight: .20

ROTISSERIE MOTOR BRACKET.

Part Number: 10184-E42
Weight: .25

ROTISSERIE SHIELD BRACKET FOR RIGHT SIDE WITH TWO MOUNTING HOLES.

Part Number: 10184-E43
Weight: .20

ROTISSERIE SHIELD BRACKET FOR LEFT SIDE WITH ONE MOUTNING HOLE.

Part Number: 10184-E44
Weight: .20

Deluxe rotisserie replacement motor. AC motor with on/off switch & 6 ft. cord. Accepts standard square spit rods.

Part Number: 60012
Weight: 1.6

Universal Heavy Duty Rotisserie Kit.

• Motor with on/off switch.
• Heavy duty forks.
• Counter balance kit.
• 33 1/2” Spit rod.
• 6” Spit rod extension.
• Other rotiss components

Part Number: 60090
Dimensions: 33 1/2
Weight: 5.01

Four prong, set of two, rotisserie meat forks for up to 5/16” spit rods. Fits our spit rods SR-5 and SR-8.

Part Number: 60120
Material: Nickel plated steel
Weight: 0.4

Rotisserie counter balance with 3/8” spit rod hole.

• Fits our spit rods SR-5 and SR-8
• Will not fit our larger rod SR-43, which is 3/8” square and requires a minimum 9/16” diameter spit rod hole

Part Number: 60215
Material: chrome steel
Weight: 0.6

Nickel plated spit rod bushing. Accepts up to 5/16” square spit rods. Use with PH-1 spit rod handle.

Part Number: BU-1
Material: Nickel plated steel
Weight: 0.1

Nickel plated spit rod bushing. Accepts up to 3/8” square spit rods. Use with PH-1 spit rod handle.

Part Number: BU-2
Material: Nickel plated steel
Weight: 0.2

304 stainless steel rotisserie motor bracket to permit motor standoff from grill. Includes two stainless steel nuts and bolts. Made in USA .

Part Number: CLA-AU0008
Dimensions: 6” x 2 15/16”
Material: stainless steel
Weight: 0.4

Stainless steel rotisserie motor mounting bracket. Requires two holes drilled 1 3/16” on center. Made in USA . Includes two mounting bolts with wing nuts.

Part Number: CLA-MS0029
Dimensions: 3” x 2 1/2”
Material: stainless steel
Weight: 0.2

Rotisserie motor bracket.

• Holds motor inverted
• Predrilled for universal fit
• Includes nuts and bolts

Note: The pre-drilled holes in the MB-1B motor mounting bracket are designed to accommodate as many existing hole patterns as possible. Still, it is possible that you may have to drill new holes.

Part Number: MB-1B
Material: Nickel plated steel
Weight: 0.2

Rotisserie bushing bracket.

• For use on grills NOT having a bushing notch in casting
• Includes nuts and bolts

Note: The pre-drilled holes in this mounting brackets are designed to accommodate as many existing hole patterns as possible. Still, it is possible that you may have to drill new holes.

Part Number: MB-2B
Material: Nickel plated steel
Weight: 0.2

Stainless steel rotisserie motor bracket.

• Holds motor inverted
• Provides shelf clearance on all models
• Includes nuts and bolts

Note: The pre-drilled mounting holes in the MB-3B rotisserie motor mounting bracket are designed to accommodate existing hole patterns approximately 1 3/8” apart. It is possible that you may have to drill new holes.

Part Number: MB-3B
Material: Stainless steel
Weight: 0.3

Set of two jumbo stainless steel meat forks. Very heavy 304 stainless steel construction. Fits up to 3/8” square spit rods.

Be sure to check your spit rod dimensions as these meat forks will not fit the larger 5/8” spit rods used on some Viking grills and others.

Part Number: MH-3SSB
Material: stainless steel
Weight: 1.0

Plastic spit rod handle with brass insert.

• Requires bushing BU-1 (5/16” square spit rods) or BU-2 (3/8” square spit rods)
• Will fit our spit rods: SR-5; SR-8; SR-43
• Requires a threaded end on the spit rod
• The mounting hole in the handle is 3/8-16 coarse thread female

Part Number: PH-1
Weight: 0.2

Rotisserie kit for Charmglow stainless 3-Burner models. THIS KIT INCLUDES A CUSTOM ”STANDOFF” MOTOR BRACKET. Includes:

• Heavy-Duty R06 rotisserie motor with stainless steel case
• SR-5 31” X 5/16” spit rod
• BU-1 spit rod bushing
• PH-1 spit rod handle
• MH-1B Chrome-plated meat forks
• MB-4B Custom standoff rotisserie motor bracket and screws
• MB-2B Rotisserie bushing bracket (for grills with no bushing notch in casting)
• Maximum 25 lbs. balanced load

Fits grills with hoods up to 26 inches wide. Be sure to measure before ordering.

NOTE: This kit does NOT include spit rod counter balance, which should on all spit rods be used to insure even weight distribution.

NOTE: Some of the parts in the kit are designed for a 5/16” rod. Rod SR-43, which is a 3/8” square rod and requires a 9/16” rod hole, will not work with some of the parts in this kit.

Part Number: RKCHAR1
Weight: 4.6

Universal rotisserie kit. THIS KIT INCLUDES AN INVERTED MOTOR BRACKET THAT POSITIONS THE MOTOR INVERTED. Includes:

• R06 stainless steel motor
• SR-5 31” X 5/16” spit rod
• BU-1 spit rod bushing
• PH-1 spit rod handle
• MH-1B Chrome-plated meat forks
• MB-3B Inverted motor mounting bracket and screws
• MB-2B Rotisserie bushing bracket (for grills with no bushing notch in casting)
• Maximum 25 lbs. balanced load

Fits grills with hoods up to 26 inches wide. Be sure to measure before ordering.

Note: The pre-drilled mounting holes in the MB-3B rotisserie motor mounting bracket are designed to accommodate existing hole patterns approximately 1 3/8” apart. It is possible that you may have to drill new holes.

NOTE: This kit does NOT include spit counter balance, which should be used to insure even weight distribution.

NOTE: Some of the parts in the kit are designed for a 5/16” rod. Rod SR-43, which is a 3/8” square rod, will not work with some of the parts in this kit.

Part Number: RK-MHP
Weight: 4.6

Universal rotisserie kit. Same as RK-MHP except with addition of longer 36” spit rod. Includes:

• R06 stainless steel motor
• SR-8 36” X 5/16” spit rod
• SR-5 31” X 5/16” spit rod
• BU-1 spit rod bushing
• PH-1 spit rod handle
• MH-1B Chrome-plated meat forks
• MB-3B Inverted motor mounting bracket and screws
• MB-2B Rotisserie bushing bracket (for grills with no bushing notch in casting)
• Maximum 25 lbs. balanced load

Fits grills with hoods up to 31 inches wide. Be sure to measure before ordering.

Note: The pre-drilled mounting holes in the MB-3B rotisserie motor mounting bracket are designed to accommodate existing hole patterns approximately 1 3/8” apart. It is possible that you may have to drill new holes.

NOTE: This kit does NOT include spit counter balance, which should be used to insure even weight distribution.

NOTE: Some of the parts in the kit are designed for a 5/16” rod. Rod SR-43, which is a 3/8” square rod, will not work with some of the parts in this kit.

Part Number: RK-MHP36
Weight: 4.6

Universal durable battery operated rotisserie motor. Conveniently eliminates the need for electric cords. Runs on 2 D cells (not included).

Part Number: RO-4
Weight: 1.0

Heavy duty stainless steel 6 1/4” x 4” x 2 1/8” cased universal rotisserie motor. On-off switch and 3 foot cord. Maximum 25 lb. balanced load. (120V, 9W, 50/60 HZ, RPM: 2.5/2.8)

Part Number: RO-6
Material: Stainless steel case
Weight: 2.0

Heavy duty nickel plated 43” x 3/8” square spit rod. Fits many larger grills. Tip is tapered to 5/16” square to fit many rotisserie motors, including all of ours. Rod only.

Fits grills with hoods up to 38 inches wide. Be sure to measure before ordering.

NOTE: The 3/8” square rod of SR-43 is slightly thicker than our other spit rods and will not work with some of the parts in the RK-MHP and RK-MHP36 rotisserie kits, which are designed for the smaller 5/16” rods.

The SR-43 rod is 3/8” square and requires a 9/16” diameter mounting hole for counter balance. The SR-43 can be used with the following parts:

• Motor RO-6 and 60013
• Meat forks MH-4B, 60150 and MH-3SSB
• Spit rod bushing BU-2
• Spit rod handle PH-1.
• Counter balance RCB-43

Part Number: SR-43
Dimensions: 43” x 3/8”
Material: Nickel plated steel
Weight: 1.7

Universal nickel plated 31” x 5/16” square spit rod.

The following parts will work on the SR-5 rod:

• All our motors
• Meat forks: 60120, 60150, and MH-3SSB
• Counter balance: RCB-B
• Spit rod bushing BU-1
• Spit rod handle PH-1.

Fits grills with hoods up to 26 inches wide. Be sure to measure before ordering.

Part Number: SR-5
Dimensions: 31” x 5/16”
Material: Nickel plated steel
Weight: 0.8

Universal nickel plated 36” x 5/16” square spit rod. Longer version of SR-5.

The following parts will work on the SR-8 rod:

• All our motors
• Meat forks: 60120, 60150, and MH-3SSB
• Counter balance: RCB-B
• Spit rod bushing BU-1
• Spit rod handle PH-1.

Fits grills with hoods up to 31 inches wide. Be sure to measure before ordering.

Part Number: SR-8
Dimensions: 36” x 5/16”
Material: Nickel plated steel
Weight: 0.9