Charbroil 466242014

Stainless steel burner for Charbroil model 466242014.

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

Stamped stainless steel cooking grids. Sold as a set of two (2). Each panel is an emitter tray and a grid-in-tray assembly, a total of 4 pieces.

Part Number: 5S482
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 17 3/4”
Material: stamped stainless steel
Weight: 10.6

Cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of two (2).

Part Number: 61122
Dimension Front-to-Back: 18 5/16”
Dimension Side-to-Side: 16 5/8”
Material: matte cast iron
Weight: 12.7

Infrared slotted stamped stainless steel cooking grid that features slotted grease drain holes for improved performance. SOLD AS A SET OF TWO (2) PIECES ONLY.
WARNING: This cooking grid set does not include the bottom trays. The grid-in-tray set of four pieces was discontinued by our supplier.

Part Number: 5S472
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 17 3/4”
Material: stamped stainless steel
Weight: 5.5

Porcelain steel Flame Tamer. Sold individually.

Part Number: 97371
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 0.55

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.16

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.88

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 0.72

Porcelain steel Flame Tamers. SET OF SIX.

Part Number: 97371-6X
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 3.3

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Part Number: 01472
Material: ceramic
Weight: 0.1

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has two (2) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03322
Dimensions: 2 5/8” x 2”
Weight: 0.5

Semi-circular, snap in heat indicator with 3 3/4” heat prob for Charbroil model 466242014.

Part Number: 00472
Dimensions: 1 3/4” x 1 1/4”
Material: stainless steel
Weight: 0.01

10” Bamboo Skewers (100 pieces)

• Ideal for grilling meat and vegetables
• Soak skewers in water about 1/2 hour before using
• Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
• Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.

Part Number: 11060
Weight: 0.6

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Aluminum foil grilling trays. Package of three.

• Heavy duty aluminum foil
• Re-usable
• Great for grilling delicate foods like fish and veggies

Part Number: 50426
Dimensions: 9” x 13”
Weight: 0.4

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7