Member's Mark CG2320401-MM

Stainless steel burner with electrode-mounting bracket. The bracket is not used on all grill models. If your model does not use a burner-mounted electrode, just ignore the bracket.

Part Number: 16251
Dimensions: 14 3/4” x 1”
Material: stainless steel
Weight: 0.6

Stainless steel cooking grids. SET OF THREE (3).

Part Number: 504S3
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 35 5/8”
Material: stainless steel wire
Weight: 12.0

Porcelain steel Heat Diffuser. Sold individually.

Part Number: 96221
Dimension Front-to-Back: 14 15/16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 0.8

SET OF FOUR/4 PACK Stainless steel heat plate. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0193-X4
Dimension Front-to-Back: 14 15/16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 2.6

Stainless steel heat plate. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0193
Dimension Front-to-Back: 14 15/16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.65

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Part Number: 04010
Material: ceramic
Weight: 0.05

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has four(4) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03344
Dimensions: 2” x 2 1/2”
Weight: 0.5

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Round heat indicator.

• Single probe
• 3 1/8” diameter
• Requires .60” mounting hole

WARNING: Please remove your old heat indicator and inspect how it is fitted onto the hood of your grill. This heat indicator has a .44” thread length; a wing nut is included. The overall length of the probe from the base of the back-side to the end of the probe measures 1 1/2".

Part Number: 00020
Dimensions: 3 1/8” x 3 1/8”
Weight: .20

6 chrome plated 18” shish-ke-bab skewers

Part Number: 63371
Weight: 0.2

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Stainless steel WOK topper with serving handles. Ideal for seafood and vegatables.

Part Number: 96321
Dimensions: 12 3/4” x 12 3/4”
Material: stainless steel
Weight: 1.6

Grill Mitt With Neoprene Palm.

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most

Part Number: 90963
Weight: 0.5