Home > Bass Pro Shops Grill Models > Bass Pro Shops DXH8303
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Bass Pro Shops grill.
Replacement gas grill parts for Bass Pro Shops model: DXH8303
DXH8303 Burners
Stainless steel tube burner.
Includes
Part Number: 18301
Dimensions: 18 5/16” x 1”
Material: stainless steel
Weight: 0.5
$32.95
DXH8303 Cooking Grids
Cast iron
cooking grids.
Porcelain treated, flat matte finish. Sold as a set of two (2).
Part Number: 67692
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 26”
Material: matte cast iron
Weight: 13.2
$93.88
DXH8303 Heat Plates
SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA
.
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0141-X4
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 3.92
$56.88
Flame Tamer, stainless steel. Made in USA
.
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0141
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.98
$21.87
DXH8303 Flame Tamers
Porcelain steel Flame Tamer. Sold individually.
Part Number: 93321
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 1.0
$25.40 $20.90
Stainless steel aftermarket Flame Tamer
heat plate.
- Stainless equivalent of part 93321
- Superior to the porcelain steel originals
- Rust and corrosion restitant
- Sold individually
- Made in USA
Part Number: 93321-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.7
$21.87
DXH8303 Igniter Components
Battery powered push button igniter.
- Has four (4) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IGEIB4-B
Weight: 0.3
$31.52
Universal four-outlet battery powered push button ignitor.
- 1.5 volt
- Has four (4) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03340
Weight: 0.5
$31.50
Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
See part 03610-X4 for a more economical 4-pack.
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
$8.67
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
$6.58
Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.
- Wire not included. Commonly used with wire part# 03610.
- Female spade connector on wire connects to male spade connector of electrode.
- If used with existing wire, confirm connecting end of wire is a female spade connector
- Usually, one electrode required per burner
NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.
Part Number: 04010
Material: ceramic
Weight: 0.05
$6.58
Push-button electronic igniter with four (4)
spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG4010
Weight: 0.2
$18.48
DXH8303 Accessories
Skewers for part 92339 kebob tray.
Part Number: 11040
Weight: 0.4
$4.75
Meat Claws. Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.
Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5
$16.16
Marinade Injector.For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.
Part Number: 14950
Material: stailess steel
Weight: 0.5
$14.41
Upright porcelain steel roasting rack with grid topper.
Part Number: 40935
Weight: 2.9
$31.80 $21.99
EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.
Part Number: 00030
Weight: 0.1
$7.60