Charbroil 464223410

Stainless steel burner for Charbroil model 464223410.

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

Stainless steel burner for Charbroil model 464223410.

Replaces Charbroil factory part# G515-2200-W1

Part Number: CBP5
Dimensions: 15 7/8” x 1”
Material: stainless steel
Weight: 1.0

stainless steel cross-over burner for Charbroil model 464223410.

Part Number: 05592
Dimensions: 6 3/8” x 0 13/16”
Material: stainless steel
Weight: 0.1

Stainless Steel cooking grids. SET OF TWO (2) panels.

• Made in USA
• Solid 5/16” 304 stainless rods
• Each panel measures 18 1/2” x 12 3/4”
• Overall dimensions: 18 1/2” x 25 1/2”

Part Number: CG-109SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 15.0

Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids.

• Made in USA
• Commercial grade 304 stainless steel
• 5/16” solid stainless rods
• Sold as a set of two (2).

Each panel measures:

• Front-to-Back: 18 1/2”
• Side-to-Side: 12 3/4”

Total Side-to-Side: 25 1/2”

Part Number: 54712-SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 5.0

Premium quality stainless steel cooking grid. Far superior to the porcelain coated steel grids it replaces.

• Made in USA
• 304 commercial grade stainless steel
• Solid 5/16” diameter solid stainless rods
• Sold individually

Fits grills made by Charbroil, Kenmore, Master Chef and others.

Part Number: 54712-SS
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 12 3/4”
Weight: 2.5

Porcelain steel Flame Tamer. Sold individually.

Part Number: 94491
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: porcelain steel
Weight: 1.1

Stainless steel aftermarket Flame Tamer.

• Stainless equivalent of part 94491
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 94491-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: stainless steel
Weight: 0.7

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Part Number: 01472
Material: ceramic
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Stainless steel WOK topper with serving handles. Ideal for seafood and vegatables.

Part Number: 96321
Dimensions: 12 3/4” x 12 3/4”
Material: stainless steel
Weight: 1.6

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3