Model: 85-3056-8

Stainless steel burner for Cuisinart model 85-3056-8.

Part Number: 1L171
Material: stainless steel
Weight: 0.9
Dimensions: 15 5/8” x 4 3/8”

Cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of three (3).

Part Number: 65253
Material: matte cast iron
Weight: 16.5
Dimensions:

• Front-To-Back: 18 3/8″
• Side-To_Side: 26 7/16″

Porcelain steel Flame Tamer. Sold individually.

Part Number: 91911
Material: porcelain steel
Weight: 1.4
Dimensions:

• Front-To-Back: 16″
• Side-To_Side: 5 15/16″

Burner-mounted electrode and 10.5” wire with female spade connector for Cuisinart model 85-3056-8. If electrode wire needs to be longer, see adapter wire part # 03198 and connector wire part # 03750.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 00170
Material: ceramic
Weight: 0.1

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Weight: 0.1
Dimensions: 17 3/4” x 1”

round trigger switch for AA and AAA spark generators; use original wires

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03153
Weight: 0.1
Dimensions: 17 3/4” x 1”

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Weight: 0.7
Dimensions: 3 3/8” x 2”

Bamboo Appetizer 7” Skewers - pack of eight. Limited to supplies on hand.

Part Number: 11040
Weight: 0.4
Dimensions: 7

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Material: stainless steel
Weight: 0.5
Dimensions: 8 1/4

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Weight: 1.5
Dimensions: 7 1/2” x 16”

Grill Mitt With Neoprene Palm.

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most

Part Number: 90963
Weight: 0.2