Jenn-Air 720-0061-LP

Cast iron burner for Jenn-Air model 720-0061-LP.

Part Number: 23301
Dimensions: 15 3/4” x 2 7/8”
Material: cast iron
Weight: 3.9

Rotisserie burner. Orifice and fitting not included. Best if used with original orifice and fitting. (If a new orifice and fitting is needed, please indicate that during check-out in the comment section.)
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive SPRING 24.

Part Number: SBB00061
Dimensions: 3 1/4” x 12 3/8”
Weight: 2.0

Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design.

NOTE: This burner is equiped with an air intake adjustable control shutter (not shown in photos) and with an air intake control screw for regulating the air/gas mixture into the burner. Natural gas applications require more air (more open screw) than lquid propane (LP). If necessary, adjust screw to get a yellow-tipped blue flame.

Part Number: 23301-CSS
Dimensions: 16” x 2 7/16”
Material: cast stainless steel
Weight: 3.2

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 13”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0194
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 13”
Material: stainless steel
Weight: 8.0

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Part Number: 62152
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 24 3/4”
Material: gloss cast iron
Weight: 13.10

Cast iron cooking grids. SET OF TWO (2) panels.

• Porcelain treated, matte finish
• Each panel measures 19 1/8” x 12 3/8”
• Overall dimensions: 19 1/8” x 24 3/4”

Part Number: CG-58P-CI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 16.7

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 12 1/2”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0190
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 12 1/2”
Material: stainless steel
Weight: 8.0

Premium universal cooking grids. Set of two (2) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 19 1/8”
• Side-to-Side: 12 3/86”

Total Side-to-Side: 24 3/4”

Part Number: 62152-UNI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 24 3/4”
Material: cast iron
Weight: 16.7

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 62152-UNI-X2 for a set of two (2).

Part Number: 62152-UNI
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 8.35

Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.80

Stainless steel Flame Tamer for Jenn-Air model 720-0061-LP.

Part Number: NGCHP2
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.7

SET OF THREE/3 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X3
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 2.4

SET OF FOUR/4 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X4
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 3.2

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

Straight thru L.P regulator with 28” hose. Adequate to 90,000 BTU.

Part Number: HR-6B
Dimensions: 28
Weight: 1.50

Stainless steel warming rack with 3/4” holes throughout the rack; an alternative warming rack to the familiar wire rod warming racks. Made in USA

Part Number: CLA-WS0316
Dimensions: 7 1/2” x 25 1/2”
Material: stainless steel
Weight: 1.7

Round heat indicator.

• Single 1 5/8” probe
• 2 1/8” diameter
• Requires 1/4” mounting hole

Part Number: 00015
Weight: 0.10

Lower heat shield; lay on existing heat shield. Dimensions of shield without brackets 13 7/8” x 15 3/8.” Made in USA

Part Number: CLA-MS0317
Dimensions: 13 7/8” x 16 3/4”
Material: stainless steel
Weight: 2.10

Back burner bracket, stainless steel (lay on top of existing bracket). Made in USA

Part Number: CLA-MS0318
Material: stainless steel
Weight: .75

10” Bamboo Skewers (100 pieces)

• Ideal for grilling meat and vegetables
• Soak skewers in water about 1/2 hour before using
• Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
• Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.

Part Number: 11060
Weight: 0.6

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3