Jenn-Air 720-0336B

Premium quality stainless steel tube burner. Sold individually, number required varies by grill. Includes:

• Made of high quality 304 stainless steel
• Spider exclusion screen
• Ignition electrode mounting holes on both sides of burner
• Back mounting hole is round, inspect your old burner

Replaces Jenn-Air factory part# 20001433A0

Part Number: CLA-BS0201
Dimensions: 16 7/8” x 1”
Material: stainless steel
Weight: 0.4

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 13”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0194
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 13”
Material: stainless steel
Weight: 8.0

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Part Number: 62152
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 24 3/4”
Material: gloss cast iron
Weight: 13.10

Cast iron cooking grids. SET OF TWO (2) panels.

• Porcelain treated, matte finish
• Each panel measures 19 1/8” x 12 3/8”
• Overall dimensions: 19 1/8” x 24 3/4”

Part Number: CG-58P-CI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 16.7

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 12 1/2”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0190
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 12 1/2”
Material: stainless steel
Weight: 8.0

Premium universal cooking grids. Set of two (2) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 19 1/8”
• Side-to-Side: 12 3/86”

Total Side-to-Side: 24 3/4”

Part Number: 62152-UNI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 24 3/4”
Material: cast iron
Weight: 16.7

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 62152-UNI-X2 for a set of two (2).

Part Number: 62152-UNI
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 8.35

Stainless steel heat plate for Jenn-Air model 720-0336B.

Replaces Jenn-Air factory part# 04005255A0

Part Number: BBQHP1
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 0.7

Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.80

Stainless steel Flame Tamer for Jenn-Air model 720-0336B.

Part Number: NGCHP2
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.7

SET OF THREE/3 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X3
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 2.4

SET OF FOUR/4 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X4
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 3.2

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X4
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.08

SET OF FIVE/5 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X5
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.85

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.77

Burner mounted replacement electrode for use with burner 15641.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Replacement electrode for use with burner 13361.

• Ceramic insulator
• 22” wire with female spade connector
• Locking nuts

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03361
Material: ceramic
Weight: 0.2

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has six (6) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Jenn-Air factory part# 07000030A1

Part Number: 03356
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Clamp-on valve with mounting bracket and ignition switch. D-Value is 12 o'clock. Stem: 8mm x 1 1/4”. 30° snout. Known to fit some Nexgrill models.

Replaces Jenn-Air factory part# 20001534A0

Part Number: 30740
Dimensions: 4” x 2 1/8”
Material: brass
Weight: 0.6

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

Skewers for part 92339 kebob tray.

Part Number: 11040
Weight: 0.4

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Stainless steel WOK topper with serving handles. Ideal for seafood and vegatables.

Part Number: 96321
Dimensions: 12 3/4” x 12 3/4”
Material: stainless steel
Weight: 1.6

Deluxe venturi brush with 11” coil spring flexible shaft

Part Number: 77310
Weight: 0.3