Jenn-Air 730-0336B

Premium quality stainless steel tube burner. Sold individually, number required varies by grill. Includes:

• Made of high quality 304 stainless steel
• Spider exclusion screen
• Ignition electrode mounting holes on both sides of burner
• Back mounting hole is round, inspect your old burner

Replaces Jenn-Air factory part# 20001433A0

Part Number: CLA-BS0201
Dimensions: 16 7/8” x 1”
Material: stainless steel
Weight: 0.4

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 13”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0194
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 13”
Material: stainless steel
Weight: 8.0

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Part Number: 62152
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 24 3/4”
Material: gloss cast iron
Weight: 13.10

Cast iron cooking grids. SET OF TWO (2) panels.

• Porcelain treated, matte finish
• Each panel measures 19 1/8” x 12 3/8”
• Overall dimensions: 19 1/8” x 24 3/4”

Part Number: CG-58P-CI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 16.7

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 19 1/4” x 12 1/2”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0190
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 12 1/2”
Material: stainless steel
Weight: 8.0

Premium universal cooking grids. Set of two (2) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 19 1/8”
• Side-to-Side: 12 3/86”

Total Side-to-Side: 24 3/4”

Part Number: 62152-UNI-X2
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 24 3/4”
Material: cast iron
Weight: 16.7

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 62152-UNI-X2 for a set of two (2).

Part Number: 62152-UNI
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 12 3/8”
Material: cast iron
Weight: 8.35

Stainless steel heat plate for Jenn-Air model 730-0336B.

Replaces Jenn-Air factory part# 04005255A0

Part Number: BBQHP1
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 0.7

Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.80

Stainless steel Flame Tamer for Jenn-Air model 730-0336B.

Part Number: NGCHP2
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 0.7

SET OF THREE/3 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X3
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 2.4

SET OF FOUR/4 PACK Stainless steel Flame Tamer/heat plate.

This heat plate also provides an economical alternative to some other heat plates with the same front-to-back dimension.

• Sold individually, number required varies.
• Shipped with protective peel-off coating, remove before use.
• Made in USA .

Part Number: CLA-TS0020-X4
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 6 3/8”
Material: stainless steel
Weight: 3.2

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X4
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.08

SET OF FIVE/5 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X5
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.85

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.77

Burner mounted replacement electrode for use with burner 15641.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Replacement electrode for use with burner 13361.

• Ceramic insulator
• 22” wire with female spade connector
• Locking nuts

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03361
Material: ceramic
Weight: 0.2

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has six (6) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Jenn-Air factory part# 07000030A1

Part Number: 03356
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

6 chrome plated 18” shish-ke-bab skewers

Part Number: 63371
Weight: 0.2

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

Abrasive scrubbing brush. Ideal for cleaning porcelain grills.

Part Number: 71448
Weight: 0.2