Kmart 640-05861277-1

Porcelain steel Flame Tamer. Sold individually.

Part Number: 97371
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 0.55

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.16

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.88

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 0.72

Porcelain steel Flame Tamers. SET OF SIX.

Part Number: 97371-6X
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 3.3

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Heat indicator with a single probe and requires a 5/16” mounting hole. Note, the back side DOES NOT have an alignment pin.

Part Number: 00021
Dimensions: 3 5/8” x 1 3/4”
Weight: 0.2

Skewers for part 92339 kebob tray.

Part Number: 11040
Weight: 0.4

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Upright porcelain steel roasting rack with grid topper.

Part Number: 40935
Weight: 2.9

Deluxe venturi brush with 11” coil spring flexible shaft

Part Number: 77310
Weight: 0.3