Home > Member's Mark Grill Models > Member's Mark 720-0778C
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Member's Mark grill.
Replacement grill parts for Member's Mark model: 720-0778C
720-0778C Burners
Stainless steel burner for Member's Mark model 720-0778C.
Part Number: 15491
Dimensions: 14 3/8” x 1”
Material: stainless steel
Weight: 0.9
$34.77
720-0778C Cooking Grids
Stainless steel
cooking grids. Sold as a set of three (3).
Part Number: 5S783
Dimension Front-to-Back: 17 5/16”
Dimension Side-to-Side: 29 3/4”
Material: stainless steel wire
Weight: 10.9
$145.89
Cast iron
cooking grids.
Porcelain treated, flat matte finish. Sold as a set of two (2).
Part Number: 64252
Dimension Front-to-Back: 17 1/4”
Dimension Side-to-Side: 28 1/8”
Material: matte cast iron
Weight: 13.12
$78.11
720-0778C Flame Tamers
Porcelain steel Flame Tamer. Sold individually.
Part Number: 90691
Dimension Front-to-Back: 15 1/4”
Dimension Side-to-Side: 4 3/4”
Material: porcelain steel
Weight: 0.8
$28.60 $19.99
SET OF FOUR/4 PACK Stainless steel Flame Tamer. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0216-X4
Dimension Front-to-Back: 15 1/4”
Dimension Side-to-Side: 4 7/8”
Material: stainless steel
Weight: 3.2
$97.17
Stainless steel Flame Tamer. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0216
Dimension Front-to-Back: 15 1/4”
Dimension Side-to-Side: 4 7/8”
Material: stainless steel
Weight: 0.80
$29.19
720-0778C Igniter Components
Universal 2 5/8” adapter wire with female round and male
spade connectors. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory
piezo spark generators have male
round connectors, while battery operated electronic spark generators usually have male
spade connectors.
- Can change male round to male spade
- Can change female spade to female round
ALL
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03198
Weight: 0.05
$5.35
Burner mounted replacement electrode for use with burner 15641.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03351
Material: ceramic
Weight: 0.2
$12.38
Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1
$19.80
Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.
Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part
03621. Inspect your system.
- 1.5 volt
- Has five (5) spark outlets (male spade connector)
- Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
- Uses a single AA battery (not included)
- Requires 7/8” mounting hole
- Overall dimensions: 2” x 3 3/8” x 2 5/8”
NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7
$39.89
Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1
$6.26
20” Ignitor adapter wire with female
spade connector and male
round connector. Used primarily on Ducane models 7100 and 7200 to extend the wire from the 03758 collector box and electrode to the electronic spark generator (igniter).
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03750
Dimensions: 1/16
Weight: 0.05
$5.77
Electrode with 24.5” wire that has a female spade/flat end for Member's Mark model 720-0778C. To lengthen the wire use adapter # 03198 and extension wire # 03750.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 04432
Dimensions: 4”
Material: ceramic
Weight: 0.1
$9.89
720-0778C Heat indicators and Meat Thermometers
Round 2 3/8” diameter heat indicator, includes one wing nut and one locking nut.
- Requires minimum 3/8” mounting hole
- Single 1 3/8” probe
- Threaded portion of probe stops at 1/2” from base
- See photo for details
Part Number: 00012
Dimensions: 2 3/8” x 2 3/8”
Weight: 0.1
$15.16
720-0778C Accessories
Skewers for part 92339 kebob tray.
Part Number: 11040
Weight: 0.4
$4.75
15” Stainless steel tong.
- Soft comfort grip
- Locking mechanism
Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14
$9.92
Marinade Injector.For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.
Part Number: 14950
Material: stailess steel
Weight: 0.5
$14.41
Upright porcelain steel roasting rack with grid topper.
Part Number: 40935
Weight: 2.9
$31.80 $21.99
Deluxe venturi brush with 11” coil spring flexible shaft
Part Number: 77310
Weight: 0.3
$9.31