Home > Member's Mark Grill Models > Member's Mark M3207ALPMember's Mark Stainless 3-burner LP gas grill with infrared searing burner, rear rotis burner, and side burner
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Member's Mark grill.
Part diagrams and owners manuals for Member's Mark model: M3207ALP
Click small image to enlarge. Click Large image to reduce. Double click for new window |
|
Replacement grill parts to fit Member's Mark model: M3207ALP
M3207ALP Burners
Stainless steel tube burner. Includes
- SS tube burner
- Electrode mounting bracket (not all models use bracket)
- Spider exclusion screen
- Adjustable air shutter.
Replaces Members Mark factory part# P02008024A
Part Number: 10241
Dimensions: 14 3/4” x 1 1/8”
Material: stainless steel
Weight: 0.7
$35.35
M3207ALP Cooking Grids
Stainless steel
cooking grid set.
- 5/16” diameter stainless rods
- 304 stainless steel
Replaces Members Mark factory part# P01604015A
Part Number: 506S3
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 32 3/8”
Material: stainless steel
Weight: 15.1
$195.93
M3207ALP Savor Plates
Stainless steel Savor Plate, also known as Flamer Tamer and
Heat Plate. Sold individually. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Replaces Members Mark factory part# P01708007B
Part Number: CLA-TS0314
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 4 1/16”
Material: stainless steel
Weight: .75
$27.28
Stainless steel
heat plate; also referred to as a flame tamer and savor plate for Member's Mark model M3207ALP.
Replaces Members Mark factory part# P01708007B
Part Number: SCHP4
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 3 13/16”
Material: stainless steel
Weight: 1.0
$27.28
M3207ALP Igniter Components
25” wire with female
spade connector on one end, and female
round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is
round connector to electrode, spade (flat) connector to igniter.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03400
Weight: 0.1
$5.35
Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.
- Wire not included. Commonly used with wire part# 03610.
- Female spade connector on wire connects to male spade connector of electrode.
- If used with existing wire, confirm connecting end of wire is a female spade connector
- Usually, one electrode required per burner
NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.
Part Number: 04010
Material: ceramic
Weight: 0.05
$6.58
Ignitor collector box with ceramic electrode and male
round connector.
- Wire not included. Commonly used with wire part# 03400.
- Designed to connect to wires with round female connector.
- If used with existing wire, confirm connector type is round where wire connects to electrode.
See part 02623-X4 for a more econimical 4 pack.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Members Mark factory part# P02609002B
Part Number: 02623
Material: ceramic
Weight: 0.2
$10.87
Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.
Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part
03621. Inspect your system.
- 1.5 volt
- Has five (5) spark outlets (male spade connector)
- Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
- Uses a single AA battery (not included)
- Requires 7/8” mounting hole
- Overall dimensions: 2” x 3 3/8” x 2 5/8”
NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7
$39.89
Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1
$19.80
Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1
$6.26
M3207ALP Accessories
shishkebob skewers
Part Number: 46074
Dimensions: 18” x 0 5/8”
Material: stainless steel
Weight: 0.4
$6.64
16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.
Part Number: 40240
Material: chrome steel
Weight: 0.9
$16.59
Deluxe 13” basting mop with hardwood handle and cotton mop head.
Part Number: 42055
Dimensions: 13
Weight: 0.2
$8.76
Upright porcelain steel roasting rack with grid topper.
Part Number: 40935
Weight: 2.9
$31.80 $21.99
Replacement heads for grill brush 77600. Set of two.
Part Number: 77650
Weight: 0.3
$6.73