Member's Mark M3207ANG

Stainless steel tube burner. Includes

• SS tube burner
• Electrode mounting bracket (not all models use bracket)
• Spider exclusion screen
• Adjustable air shutter.

Replaces Members Mark factory part# P02008024A

Part Number: 10241
Dimensions: 14 3/4” x 1 1/8”
Material: stainless steel
Weight: 0.7

Stainless steel cooking grid set.

• 5/16” diameter stainless rods
• 304 stainless steel

Replaces Members Mark factory part# P01604015A

Part Number: 506S3
Dimension Front-to-Back: 19 1/8”
Dimension Side-to-Side: 32 3/8”
Material: stainless steel
Weight: 15.1

Stainless steel Savor Plate, also known as Flamer Tamer and Heat Plate. Sold individually. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Members Mark factory part# P01708007B

Part Number: CLA-TS0314
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 4 1/16”
Material: stainless steel
Weight: .75

Stainless steel heat plate; also referred to as a flame tamer and savor plate for Member's Mark model M3207ANG.

Replaces Members Mark factory part# P01708007B

Part Number: SCHP4
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 3 13/16”
Material: stainless steel
Weight: 1.0

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Part Number: 04010
Material: ceramic
Weight: 0.05

Ignitor collector box with ceramic electrode and male round connector.

• Wire not included. Commonly used with wire part# 03400.
• Designed to connect to wires with round female connector.
• If used with existing wire, confirm connector type is round where wire connects to electrode.

See part 02623-X4 for a more econimical 4 pack.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Members Mark factory part# P02609002B

Part Number: 02623
Material: ceramic
Weight: 0.2

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

6 chrome plated 18” shish-ke-bab skewers

Part Number: 63371
Weight: 0.2

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

Grill Mitt With Neoprene Palm.

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most

Part Number: 90963
Weight: 0.5