Home > Nexgrill Grill Models > Nexgrill 720-0830A
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Nexgrill grill.
Replacement grill parts to fit Nexgrill model: 720-0830A
720-0830A Burners
Stainless steel tube burner for Nexgrill model 720-0830A.
Part Number: 10381
Dimensions: 15 x 1
Material: stainless steel
Weight: 0.5
$32.21
720-0830A Cooking Grids
Stainless steel
cooking grid. Sold as a set of two (2).
Part Number: 5S732
Dimension Front-to-Back: 17 3/16
Dimension Side-to-Side: 26 3/8
Material: stainless steel clad wire
Weight: 10.3
$120.13
720-0830A Flame Tamers
Porcelain steel Flame Tamer. Sold individually.
Part Number: 97371
Dimension Front-to-Back: 14 9/16
Dimension Side-to-Side: 3 1/4
Material: porcelain steel
Weight: 0.55
$21.54
SET OF THREE/3 PACK Stainless steel
heat plate/Flame Tamer. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a height that is 3/16 taller than 97371. Determine if this matters to you and order the part that best replaces your old
heat plate.
Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16
Dimension Side-to-Side: 3 1/4
Material: stainless steel
Weight: 2.16
$48.77
SET OF FOUR/4 PACK Stainless steel
heat plate/Flame Tamer. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a height that is 3/16 taller than 97371. Determine if this matters to you and order the part that best replaces your old
heat plate.
Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16
Dimension Side-to-Side: 3 1/4
Material: stainless steel
Weight: 2.88
$62.52
Stainless steel
heat plate/Flame Tamer. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a height that is 3/16 taller than 97371. Determine if this matters to you and order the part that best replaces your old
heat plate.
Part Number: CLA-TS0157
Dimension Front-to-Back: 14 9/16
Dimension Side-to-Side: 3 1/4
Material: stainless steel
Weight: 0.72
$17.61
Porcelain steel Flame Tamers. SET OF SIX.
Part Number: 97371-6X
Dimension Front-to-Back: 14 9/16
Dimension Side-to-Side: 3 1/4
Material: porcelain steel
Weight: 3.3
Image not available
$105.36
720-0830A Igniter Components
Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03152
Dimensions: 17 3/4 x 1
Weight: 0.1
$19.80
Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.
Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part
03621. Inspect your system.
- 1.5 volt
- Has five (5) spark outlets (male spade connector)
- Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
- Uses a single AA battery (not included)
- Requires 7/8 mounting hole
- Overall dimensions: 2 x 3 3/8 x 2 5/8
NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03352
Dimensions: 3 3/8 x 2
Weight: 0.7
$39.89
Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03621
Dimensions: 1 1/8 x 1 1/8
Weight: 0.1
$6.26
electrode
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 07370
Dimensions: 4 3/16 x 0 3/4
Material: ceramic
Weight: 0.1
$10.81
720-0830A Heat indicators and Meat Thermometers
Heat indicator with a single probe and requires a 5/16 mounting hole. Note, the back side DOES NOT have an alignment pin.
Part Number: 00021
Dimensions: 3 5/8 x 1 3/4
Weight: 0.2
$15.90
720-0830A Accessories
6 deluxe chrome plated 22” shish-ke-bab skewers with wooden handles
Part Number: 40538
Material: chrome steel
Weight: 1.1
$15.59
15 Stainless steel tong.
- Soft comfort grip
- Locking mechanism
Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14
$9.92
economy basting brushes. Two brushes, 7.5” long.
Part Number: 43054
Weight: 0.1
$5.77
Aluminum foil grilling trays. Package of three.
- Heavy duty aluminum foil
- Re-usable
- Great for grilling delicate foods like fish and veggies
Part Number: 50426
Dimensions: 9 x 13
Weight: 0.4
$8.64
Grill Mitt With Neoprene Palm. 16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most
Part Number: 90963
Weight: 0.5
$17.59