Igniter Components for Outback grills

Push-Button self-grounding piezo spark generator; requiers 3/4” mounting hole for some Outback grills. Primary connector is a round male connector, so connecting wire needs to be female round connector. If needed, see part# 03199C for a short adapter wire that converts flat female spade connectors to female round. Secondary connector is a flat male spade connector used to conduct spark to a secondary electrode, such as a side burner, or used as a ground in some applications. See ground wire part# 03620. For more information, see our article Ignition 101.

Part Number: 03120
Weight: 0.1

Universal 5 1/2” jumper wire with female spade ends to close off unused pair of outlets in battery-powered spark generator, or use as an adaptor wire for some Outback grills.
NOTICE: EACH END HAS A PLASTIC PROTECTOR CAP.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03197
Weight: 0.05

Universal 2 5/8” adapter wire with female round and male spade connectors for some Outback grills. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory piezo spark generators have male round connectors, while battery operated electronic spark generators usually have male spade connectors.

• Can change male round to male spade
• Can change female spade to female round

ALL

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03198
Weight: 0.05

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover for some Outback grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Universal battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has one (1) terminal (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03310
Weight: 0.3

Universal volt battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03320
Weight: 0.3

Universal battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03330
Weight: 0.5

Universal three-outlet battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03333
Dimensions: 2 9/16” x 2”
Weight: 0.5

Universal battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has (5) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03335
Dimensions: 2 5/8” x 2”
Weight: 0.3

Universal four-outlet battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Universal battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has six (6) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03350
Weight: 0.7

4-outlet 9 volt spark generator for some Outback grills. Use jumper wire 03197 for 2-outlet applications.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03370
Dimensions: 3 7/8” x 2”
Weight: 0.5

Universal battery powered push button ignitor for some Outback grills.

• 1.5 volt
• Has five (5) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03380
Dimensions: 3 5/16” x 2”
Weight: 0.7

25” wire with female spade connector on one end, and female round connector on the other end for some Outback grills. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors) for some Outback grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

Ignition connection wire used to connect battery powered spark generators to electrodes for some Outback grills. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors for some Outback grills. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

20” Ignitor adapter wire with female spade connector and male round connector for some Outback grills. Used primarily on Ducane models 7100 and 7200 to extend the wire from the 03758 collector box and electrode to the electronic spark generator (igniter).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03750
Dimensions: 1/16
Weight: 0.05

Universal adapter wire with male round and female spade connectors for some Outback grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03751
Weight: 0.05

Collector box and electrode assembly for some Outback grills. Tongue style burner mounted collector box with ceramic electrode, 15” wire, and female round connector. Not designed to mount on original equipment burners. Fits our stainless steel burners with special mounting bracket only. Will NOT fit on cast iron burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03900
Material: ceramic
Weight: 0.2

Universal collector box with electrode and wire for some Outback grills. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

Universal 3 outlet rotary spark generator for some Outback grills. Includes knob.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-8B
Weight: 0.3

Snap In Piezo Ignitor for some Outback grills. Fits Weber Genesis Silver A,B,C and Newer Spirit E310 & E320.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-9B
Weight: 0.2