Sams 720-0584

Premium quality stainless steel tube burner. Sold individually, number required varies by grill. Includes:

• Made of high quality 304 stainless steel
• Spider exclusion screen
• Ignition electrode mounting holes on both sides of burner
• Back mounting hole is round, inspect your old burner

Replaces Sams factory part# 10000308A0

Part Number: CLA-BS0201
Dimensions: 16 7/8” x 1”
Material: stainless steel
Weight: 0.4

Burner made of premium quality 304 stainless steel. Sold individually, number required varies by grill.

Replaces Sams factory part# 10000284A0

Part Number: CLA-BS0199
Dimensions: 15 13/16” x 4 1/2”
Material: stainless steel
Weight: 0.7

Burner made of commercial 304 grade stainless steel. Sold individually, number required varies by grill.

Replaces Sams factory part# 10000284A0

Part Number: JATB1
Dimensions: 15 7/8” x 4 1/2”
Material: stainless steel
Weight: 0.7

Stainless burner support bracket. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-MS0066
Dimensions: 16 11/16
Material: stainless steel
Weight: 1.0

Stainless steel Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Sams factory part# 04000504A0

Part Number: CLA-TS0136
Dimension Front-to-Back: 17 5/16”
Dimension Side-to-Side: 5 13/16”
Material: stainless steel
Weight: 0.94

Stainless steel Flame Tamer for Sams model 720-0584.

Replaces Sams factory part# 04000504A0

Part Number: NGCHP4
Dimension Front-to-Back: 17 5/16”
Dimension Side-to-Side: 5 7/8”
Material: stainless steel
Weight: 0.7

Burner mounted replacement electrode for use with burner 15641.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Replacement electrode for use with burner 13361.

• Ceramic insulator
• 22” wire with female spade connector
• Locking nuts

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03361
Material: ceramic
Weight: 0.2

shishkebob skewers

Part Number: 46074
Dimensions: 18” x 0 5/8”
Material: stainless steel
Weight: 0.4

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7