Home > Sams Grill Models > Sams MG3208SLPMember's Mark Stainless 3-burner LP gas grill with infrared searing burner, rear rotis burner, and side burner
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Sams grill.
Part diagrams and owners manuals for Sams model: MG3208SLP
Click small image to enlarge. Click Large image to reduce. Double click for new window |
|
Replacement BBQ grill parts for Sams model: MG3208SLP
MG3208SLP Burners
Stainless steel tube burner. Includes
- SS tube burner
- Electrode mounting bracket (not all models use bracket)
- Spider exclusion screen
- Adjustable air shutter.
Replaces Sams factory part# P020080244
Part Number: 10241
Dimensions: 14 3/4” x 1 1/8”
Material: stainless steel
Weight: 0.7
$35.35
MG3208SLP Savor Plates
Stainless steel Savor Plate, also known as Flamer Tamer and
Heat Plate. Sold individually. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Replaces Sams factory part# P017080074
Part Number: CLA-TS0314
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 4 1/16”
Material: stainless steel
Weight: .75
$27.28
Stainless steel
heat plate; also referred to as a flame tamer and savor plate for Sams model MG3208SLP.
Replaces Sams factory part# P017080074
Part Number: SCHP4
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 3 13/16”
Material: stainless steel
Weight: 1.0
$27.28
MG3208SLP Igniter Components
25” wire with female
spade connector on one end, and female
round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is
round connector to electrode, spade (flat) connector to igniter.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03400
Weight: 0.1
$5.35
Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
See part 03610-X4 for a more economical 4-pack.
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
$8.67
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
$6.58
Ignitor collector box with ceramic electrode and male
round connector.
- Wire not included. Commonly used with wire part# 03400.
- Designed to connect to wires with round female connector.
- If used with existing wire, confirm connector type is round where wire connects to electrode.
See part 02623-X4 for a more econimical 4 pack.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Sams factory part# P02609030M
Part Number: 02623
Material: ceramic
Weight: 0.2
$10.87
Universal battery powered push button ignitor.
- 1.5 volt
- Has six (6) terminals (male spade connector)
- Uses a single AA battery (not included))
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Overall dimensions: 2” x 3 3/8” x 3”
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Sams factory part# P02502265C
Part Number: 03350
Weight: 0.7
$31.96
46” Wire with female
spade connectors and square plastic connectors.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IG-30B
Dimensions: 46
Weight: 0.1
$7.10
MG3208SLP Accessories
Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.
Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90
$25.40
Meat Claws. Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.
Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5
$16.16
Deluxe 13” basting mop with hardwood handle and cotton mop head.
Part Number: 42055
Dimensions: 13
Weight: 0.2
$8.76
Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.
Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5
$22.60
deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.
Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7
$25.57