Home > Sure Heat Grill Models > Sure Heat CS784LP
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Sure Heat grill.
Replacement BBQ grill parts for Sure Heat model: CS784LP
CS784LP Burners
Stainless steel burner.
NOTE: Before you order this burner, remove the old burner from your grill and measure and compare to this burner. The manufacturer made different burners for certain years in which the same model number was used.
Part Number: 16731
Dimensions: 17 1/8” x 0 3/4”
Material: stainless steel
Weight: 0.6
$31.72
CS784LP Burner Brackets and Carryovers
Stainless steel carryover. Made in USA
.
Part Number: CLA-MS0098
Dimensions: 2 7/8” x 15”
Material: stainless steel
Weight: 0.55
$30.12
CS784LP Cooking Grids
Cast iron
cooking grids (set of 3).
Porcelain treated, matte finish.
Part Number: 65993
Dimension Front-to-Back: 18 1/8”
Dimension Side-to-Side: 30 9/16”
Material: matte cast iron
Weight: 25.5
$154.28
CS784LP Flavor Grids
Porcelain steel Flavor Grid. Sold individually, number required varies by grill.
Part Number: 93031
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: porcelain steel
Weight: 1.1
$27.56
Large Flavor Grid. Stainless steel. Only one of these are used on the grill. This part has an extended side that faces the infrared burner and acts as a heat shield. The other Flavor Grids do not have this shield.
- One required per grill.
- Sold individually.
- Made in USA .
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use. Made in USA
Part Number: CLA-TS0072
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 1.2
$31.72
Flavor grid, stainless steel. Made in USA
.
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0140
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.98
$28.91
CS784LP Igniter Components
Battery powered push button igniter.
- Has four (4) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IGEIB4-B
Weight: 0.3
$31.52
Universal four-outlet battery powered push button ignitor.
- 1.5 volt
- Has four (4) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03340
Weight: 0.5
$31.50
Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
See part 03610-X4 for a more economical 4-pack.
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
$8.67
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
$6.58
Ceramic electrode and 40” wire with female
spade connector.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 06730
Material: ceramic
Weight: 0.1
$8.81
Push-button electronic igniter with four (4)
spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG4010
Weight: 0.2
$18.48
CS784LP Heat indicators and Meat Thermometers
heat indicator for Sure Heat model CS784LP.
Part Number: 00013
Dimensions: 3 3/8” x 2 1/16”
Weight: 0.2
$15.90
CS784LP Accessories
Shish-ke-bab set. 6 chrome plated 14” skewers with convenient folding rack; folds out to 10” x 13 3/4”.
Part Number: 41338
Weight: 1.1
$22.60
15” Stainless steel tong.
- Soft comfort grip
- Locking mechanism
Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14
$9.92
Marinade Injector.For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.
Part Number: 14950
Material: stailess steel
Weight: 0.5
$14.41
Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.
Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5
$22.60
EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.
Part Number: 00030
Weight: 0.1
$7.60