Sure Heat SFR30

Stainless steel burner.

NOTE: Before you order this burner, remove the old burner from your grill and measure and compare to this burner. The manufacturer made different burners for certain years in which the same model number was used.

Part Number: 16731
Dimensions: 17 1/8” x 0 3/4”
Material: stainless steel
Weight: 0.6

Stainless Flavor Grid (heat plate/Flame Tamer). Sold individually, number required varies.

Part Number: AMHP1
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 3 7/16”
Material: stainless steel
Weight: 1.0

SET OF THREE/3 PACK Flavor Grid, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0152-X3
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 3.6

SET OF FOUR/4 PACK Flavor Grid, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0152-X4
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 4.8

Flavor Grid, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0152
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 1.2

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Ceramic electrode and 40” wire with female spade connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 06730
Material: ceramic
Weight: 0.1

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

Universal premium quality stainless steel warming rack. You simply can't buy a better quality warming rack than this, which weighs in at almost 5lbs of solid 304 grade stainless steel. This super heavy-duty warming rack was made to replace the porcelain coated steel racks found on BBQ grills made by The Great Outdoors Grill Company, but can be used in many other different grills.

• Far superior to the original porcelain coated steel rack
• Rests on your existing cooking grids.
• Solid 1/4” 304 stainless steel rods.
• Stands 3.75 inches tall.
• Made in USA .

WARNING: Before ordering this universal rack, please verify your grill has enough space to accommodate it. If you need to return, you will be responsible for return shipping, and the original out bound shipping fee will be deducted from the refund. What's required?

• Your grill needs to be at least 24” wide on the inside . The warming rack is 6.25” front to back and stands 3.75” tall.
• Notice the shape of the warming rack. Determine if the lid of your grill can easily close with the warming rack inside along with food placed on top of the rack.
  
  Part Number: CLA-WS0040
  Dimensions: 6 1/4” x 22 7/8”
  Material: stainless steel
  Weight: 4.8

shishkebob skewers

Part Number: 46074
Dimensions: 18” x 0 5/8”
Material: stainless steel
Weight: 0.4

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7