Vermont Castings VC0680N

AZ001503-R Replacement cast iron burner. Includes venturi mounting bolts. Venturi not included, sold separately. Replaces original Great Outdoors part# AZ001503.

Fits models:

• 8000
• 8100
• 8500

NOTE: The original Great Outdoors cast brass and cast iron burners are no longer available. This replacement burner is slightly smaller, but fully functional. It's ”legs” are not threaded, so it simply sits in the bottom of the grill.

Part Number: AZ001503-R
Dimensions: 15 1/2” x 8”
Material: cast iron
Weight: 7.7

Replacement stainless steel burner. Includes venturi mounting bolts/screws. Venturi not included, sold separately.

NOTE: The original cast brass and cast iron burners are no longer available. This replacement stainless steel version is slightly smaller, but supports the same amount of gas with good heat distribution. The stainless steel version will not screw down into the base of the grill, but simply sits in the bottom of the grill using adjustable support brackets, which are included.

Part Number: AZ001503-SS
Dimensions: 15 7/8” x 8”
Material: stainless steel
Weight: 2.5

Spider exclusion screens. Installs over venturi air shutters to keep spiders out. Approximately 7/8” in diameter and 1” long.

Part Number: 70002
Dimensions: 1” x 7/8”
Material: stainless steel
Weight: 0.1

Universal venturi (includes gaskets and screws). Fits grill models VC0680AP, VC0680N, and VC0680P with ”B” style (angled console) pillar. (2) required. Original venturi for models with B style pillar no longer available.


Part Number: 72401
Dimensions: 7 1/2” x 11”
Material: zinc plated steel
Weight: 0.3

AZ000506-R Replacement venturi tube. Includes gasket and screws. Replaces original Great Outdoors part# AZ000506.

Fits models:

• 5500
• 8000
• 8100
• 8500

Part Number: AZ000506-R
Dimensions: 5 1/2” x 1 1/2”
Material: zinc plated steel
Weight: 0.7

two venturi gaskets with screws for Vermont Castings model VC0680N.

Part Number: 00400
Dimensions: 3 1/16” x 1 1/4”
Weight: 0.05

Single Gasket Kit Economy Burners for Vermont Castings model VC0680N.

Part Number: SHK4
Weight: 0.01

Cast iron cooking grids. Porcelain enameled, glossy finish. Sold as a set of two (2).

Part Number: 66162
Dimension Front-to-Back: 17 1/8”
Dimension Side-to-Side: 24 7/8”
Material: gloss cast iron
Weight: 10.14

AZ001600-GCI Cooking Grid set for Great Outdoors 1000, 8000, 8100, and 8500 series gas grills. Porcelain enameled, glossy finish cast iron. Sold as a set of two (2).

These grills were originally equipped with either two (2) porcelain coated steel wire grids (original part# AF000102), or two (2) porcelain cast iron grids (original part# AZ001600). Original parts are no longer available. This part is a great replacement for AF001600 if you prefer the cast iron cooking grids.

Replaces Vermont Castings factory part# AZ001600

Part Number: AZ001600-GCI
Dimension Front-to-Back: 17 1/8”
Dimension Side-to-Side: 24 7/8”
Material: gloss cast iron
Weight: 10.15

AZ001600-SS Cooking Grid for Great Outdoors 1000, 8000, 8100, and 8500 series BBQ grills. Heavy duty stainless steel. If you're looking for the best, you've found it. Each panel is over 7 pounds of solid stainless.

• Large diameter 5/16” stainless steel rods.
• Commercial grade 304 stainless.
• Sold individally.
• Made in USA .

Originally equipped with either two (2) porcelain coated steel wire grids (original part# AF000102), or two (2) porcelain cast iron grids (original part# AZ001600), these parts are no longer available. This stainless part is a high quality replacement for AF001600. The grid is slightly wider than the original, creating a snug fit.

Part Number: AZ001600-SS
Dimension Front-to-Back: 17”
Dimension Side-to-Side: 12 5/8”
Material: stainless steel
Weight: 7.2

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 7 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 17” x 12 5/8”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0114
Dimension Front-to-Back: 17”
Dimension Side-to-Side: 12 5/8”
Material: stainless steel
Weight: 7.2

Cast iron cooking grid. Porcelain enameled, glossy finish. Sold individually.

Part Number: 66162-1PC
Dimension Front-to-Back: 17 1/8”
Dimension Side-to-Side: 12 7/16”
Material: gloss cast iron
Weight: 5.1

Carbon steel rock grate with 1/4” rods. Made in USA .

Replaces Vermont Castings factory part# AF000202

Part Number: CLA-RX0010
Dimensions: 14 3/4” x 22 5/8”
Material: carbon steel
Weight: 5.3

Heat Shield. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Vermont Castings factory part# AI000204

Part Number: CLA-MS0067
Dimensions: 10 1/4” x 16 3/8”
Material: stainless steel
Weight: 1.4

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal collector box with electrode and wire. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

Collector box and ceramic electrode with male spade connector. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, but no ground wire, see ground wire 03620.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000103

Part Number: 03800
Material: ceramic
Weight: 0.2

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000203

Part Number: 03400
Weight: 0.1

Rotary piezo spark generator. Two round connector leads send spark to both main burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000303

Part Number: 03220
Weight: 0.2

Premium quality polyester lined vinyl cover, E-Z on velcro tabs. For large grills, full length.

• 60” left to right
• 20” front to back
• 42” top to bottom

Please measure your grill to determine which cover fits best. Avoid too snug a fit as a slightly oversized cover is easier to take off and put back on.

Part Number: CV-4PREM
Material: Vinyl
Weight: 3.5

Silver plastic control knob. Replaces original part# 50002552. Can also be used to replace knob part# AZ000703.

• Off position D-Value: 6 o'clock
• Knob diameter: 2 3/16”
• Socket diameter: 8mm
• Knob shaft: None

Part Number: 02552
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.1

24” LP hose and regulator with QCC-1 connection.

• For use on ”new style” QCC-1 tanks.
• Consists of hose part# 01000 and regulator part# 00920.
• Hose end with SAE 3/8” female flare fitting connects to grill.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. See our flare fitting description for information on measuring and sizes.

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

Premium quality stainless steel warming rack. You simply can't buy a better quality warming rack than this, which weighs in at almost 5lbs of solid 304 grade stainless steel. This super heavy-duty warming rack was made to replace AF000303, the porcelain coated steel racks found on BBQ grills made by The Great Outdoors Grill Company, but can fit in any grill with 23 inches or more for the rack to sit on.

• Far superior to the original porcelain coated steel rack
• Rests on your existing cooking grids.
• Solid 1/4” 304 stainless steel rods.
• Stands 3 inches tall.
• Made in USA .

WARNING: Before ordering this universal rack, please verify your grill has enough space to accomodate it. At least 23” inside the closed lid is required.

Replaces Vermont Castings factory part# AF000303

Part Number: AF000303-SS
Dimensions: 6 1/4” x 22 3/4”
Material: stainless steel
Weight: 4.8

T manifold for twin valves with 3/8” male flare. Fits Charbroil late model grills with LP hoses crimped to the manifold.

Part Number: 34100
Dimensions: 2” x 1 5/16”
Material: brass
Weight: 0.3

Durable 2 5/16” round briquettes

• Self-cleaning
• Control flare-ups while holding an even heat pattern.
• About 53 pieces, covers approximately 275 sq. inches.
• Fits all gas grills

Replaces Vermont Castings factory part# AQ000102

Part Number: BQ-5
Weight: 7.2

High quality, long lasting ceramic briquettes. 59 flat top pyramid-shaped briquettes per box. Placed 1/2” apart, 59 briquetes will cover about 368 square inches. This is an area roughly 15” x 24”.

• Top quality product
• Each briquette measure 2” x 2”
• Self cleaning
• Great heat distibution, retains heat longer
• Can be used on all grills that use briquettes or lava rock
• Use a single layer (multiple layers can reduce temperatures)

NOTE: These high quality ceramic briquetes are available in 59 count, 70 count, and 90 count qantities.

• 59 briquetes covers an area apprimately 15” x 24”
• 70 briquetes covers an area apprimately 17” x 26”
• 90 briquetes covers an area apprimately 17” x 33”

Made in USA
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive mid April.

Part Number: CLA-AC0394
Dimensions: 2” x 2”
Material: ceramic
Weight: 7.65

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Cast aluminum griddle

Part Number: 91652
Dimensions: 19 1/2” x 10 3/4”
Material: aluminum
Weight: 3.0

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7