Model: BR4GRILL

Stainless steel tube burner.

Includes
• SS tube burner
• Electrode mounting bracket (not all models use bracket)
• Spider exclusion screen
• Adjustable air shutter.

NOTE: Some earlier versions of this burner, which are no longer available, were a bit larger in diameter. Some models may not need the electrode tab.
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive mid Oct.

Part Number: 12411
Dimensions: 16 1/2” x 1”
Material: stainless steel
Weight: 0.6

Cast iron cooking grids. SET OF TWO (2) panels.

• Porcelain treated, matte finish
• Each panel measures 17 3/4” x 11 1/2”
• Overall dimensions: 17 3/4” x 23”

Part Number: CG-101PCI-X2
Dimension Front-to-Back: 17 3/4”
Dimension Side-to-Side: 23”
Material: cast iron
Weight: 11.6

Stainless steel Heat Tent/ Flame Tamer. Sold individually, number required varies.

Part Number: BMHP8
Dimension Front-to-Back: 15 3/8”
Dimension Side-to-Side: 3 9/16”
Material: stainless steel
Weight: 0.5

SET OF FOUR/4 PACK Stainless steel Heat Distribution Plates. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0147-X4
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 3 5/8”
Material: stainless steel
Weight: 2.16

SET OF FIVE/5 PACK Stainless steel Heat Distribution Plates. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0147-X5
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 3 5/8”
Material: stainless steel
Weight: 2.7

Stainless steel Heat Distribution Plate. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0147
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 3 5/8”
Material: stainless steel
Weight: 0.54

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Part Number: 04010
Material: ceramic
Weight: 0.05

Premium quality polyester lined vinyl cover, E-Z on velcro tabs. For large grills, full length.

• 65” left to right
• 23” front to back
• 42” top to bottom

Please measure your grill to determine which cover fits best. Avoid too snug a fit as a slightly oversized cover is easier to take off and put back on.

Part Number: CV-5PREM
Material: Vinyl
Weight: 3.5

Universal 2 5/16” knob.

• Selectable D-Value
• Selectable socket diameter - 6mm or 8mm.
• Selectable shaft length - flush, 1/4”, or 1 5/8”. Shafts can also be trimmed to desired length.
• Includes 6 shaft inserts and set screw.
• Fits any grill with inside bezel diameter greater than 2 5/16” (the knob diameter).

Part Number: 02342
Dimensions: 2 5/16” x 2 5/16”
Material: plastic
Weight: 0.20

Universal premium quality stainless steel warming rack. You simply can't buy a better quality warming rack than this, which weighs in at almost 5lbs of solid 304 grade stainless steel. This super heavy-duty warming rack was made to replace the porcelain coated steel racks found on BBQ grills made by The Great Outdoors Grill Company, but can be used in many other different grills.

• Far superior to the original porcelain coated steel rack
• Rests on your existing cooking grids.
• Solid 1/4” 304 stainless steel rods.
• Stands 3.75 inches tall.
• Made in USA .

WARNING: Before ordering this universal rack, please verify your grill has enough space to accommodate it. If you need to return, you will be responsible for return shipping, and the original out bound shipping fee will be deducted from the refund. What's required?

• Your grill needs to be at least 24” wide on the inside . The warming rack is 6.25” front to back and stands 3.75” tall.
• Notice the shape of the warming rack. Determine if the lid of your grill can easily close with the warming rack inside along with food placed on top of the rack.
  
  Part Number: CLA-WS0040
  Dimensions: 6 1/4” x 22 7/8”
  Material: stainless steel
  Weight: 4.8

Round heat indicator.

• Single 1 5/8” probe
• 2 1/8” diameter
• Requires 1/4” mounting hole

Part Number: 00015
Weight: 0.10

shishkebob skewers

Part Number: 46074
Dimensions: 18” x 0 5/8”
Material: stainless steel
Weight: 0.4

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3