Model: SGR30M

304 Stainless steel Infrared rear rotisserie burner with ceramic wafer. For use with both liquid propane (LP) and natural gas grills. 8,000 BTU. Orifice not included. Use old orifice or purchase our orifice part# CLA-VB0245 for LP, or part# CLA-VB0246 for natural gas applications.

Dimensions:

• Maximum overall length, including mounting tab on one end: 17”
• Maximum width: 3 3/8”
• Burner box 15 3/8” x 3 3/8”
• Mounting holes: 16 1/8” on center

Part Number: CLA-BL0229
Material: stainless steel and ceramic
Weight: 3.0
Dimensions: 3 3/8” x 17”

Stainless steel triple burner set. Electrodes not incuded.

Part Number: TUST3
Material: stainless steel
Weight: 3.5
Dimensions: 18” x 15 3/4”

Stainless steel cooking grids with solid 1/4” rods (set of 3) for Costco model SGR30M.

Part Number: 53S33
Material: stainless steel wire
Weight: 10.0
Dimensions:

• Front-To-Back: 17 1/2″
• Side-To_Side: 27 3/8″

Large Flavor Grid. Stainless steel. Only one of these are used on the grill. This part has an extended side that faces the infrared burner and acts as a heat shield. The other Flavor Grids do not have this shield.

• One required per grill.
• Sold individually.
• Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use. Made in USA

Part Number: CLA-TS0072
Material: stainless steel
Weight: 1.2
Dimensions:

• Front-To-Back: 15 3/16″
• Side-To_Side: 5 7/16″

Flavor grid, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0140
Material: stainless steel
Weight: 0.98
Dimensions:

• Front-To-Back: 15 3/16″
• Side-To_Side: 5 7/16″

Stainless steel Flavor Grid for Costco model SGR30M.

Part Number: SONHP1
Material: stainless steel
Weight: 0.6
Dimensions:

• Front-To-Back: 15 3/16″
• Side-To_Side: 5 7/16″

Genuine OEM 21” wire for side burner or other applications. Both ends are female spade connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 10342-T12
Weight: 0.05
Dimensions: 21

Ceramic electrode with mounting hardware.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 01683
Material: ceramic
Weight: 0.1

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

#63 orifice for infrared burner CLA-BL0229; use on liquid propane (LP) gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VB0245
Material: stainless steel and ceramic
Weight: 0.3
Dimensions: 3 3/8” x 17 1/4”

#55 orifice for infrared burners use on natural Gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VB0246
Material: stainless steel and ceramic
Weight: 0.3
Dimensions: 3 3/8” x 17 1/4”

Stainless steel electrode shield. Made in USA

Part Number: CLA-MS0091
Material: stainless steel
Weight: 0.4
Dimensions: 14 1/8” x 3 3/8”

Bamboo Appetizer 7” Skewers - pack of eight. Limited to supplies on hand.

Part Number: 11040
Weight: 0.4
Dimensions: 7

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Material: stainless steel
Weight: 0.5
Dimensions: 8 1/4

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Porcelain Coated Square Wok Topper.
12” x 12” x 2” porcelain coated grilling wok with stainless steel handles and perforations. The single draw design improves functionality and rigidity, it also makes it much easier to clean.

Part Number: 98121
Material: porcelain steel
Weight: 1.6

Extra Wide Nylon Grill Brush

Brush anywhere on the grill, deep into the corners, between the grids, and in broad strokes along the surface. The triangular shaped head of this brush is ideal for cleaning anywhere. 17 in. overall length with a 6. in. wide head. Nylon bristles, wire shaft and resin handle.

*For use on a cool grill.

Part Number: 77643
Weight: 0.5