Grand Hall SS54-LP

Cast iron burner for Grand Hall model SS54-LP.

Replaces Grand Hall factory part# P02001009E

Part Number: 23311
Dimensions: 13 7/8” x 2 1/2”
Material: cast iron
Weight: 3.5

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Replaces Grand Hall factory part# P01615015A

Part Number: 60662
Dimension Front-to-Back: 16 15/16”
Dimension Side-to-Side: 23 1/2”
Material: gloss cast iron
Weight: 13.14

Premium universal cooking grids. Set of two (2). Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 16 15/16”
• Side-to-Side: 11 3/4”

Total Side-to-Side: 23 1/2”

Part Number: 60662-UNI-X2
Dimension Front-to-Back: 16 15/16”
Dimension Side-to-Side: 23 1/2”
Material: cast iron
Weight: 14.30

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 60662-UNI-X2 for a set of two (2).

Part Number: 60662-UNI
Dimension Front-to-Back: 16 15/16”
Dimension Side-to-Side: 11 3/4”
Material: cast iron
Weight: 7.15

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually, number required varies.

Part Number: 60663-1PC
Dimension Front-to-Back: 16 15/16”
Dimension Side-to-Side: 11 3/4”
Material: cast iron
Weight: 6.7

Porcelain steel Flame Tamer for Grand Hall model SS54-LP.

Replaces Grand Hall factory part# P01705006E

Part Number: 90161
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 7 13/16”
Material: porcelain steel
Weight: 1.4

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0128
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 7 13/16”
Material: stainless steel
Weight: 1.03

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Ignitor collector box with ceramic electrode and male round connector.

• Wire not included. Commonly used with wire part# 03400.
• Designed to connect to wires with round female connector.
• If used with existing wire, confirm connector type is round where wire connects to electrode.

See part 02623-X4 for a more econimical 4 pack.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Grand Hall factory part# P02609002B

Part Number: 02623
Material: ceramic
Weight: 0.2

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Grand Hall factory part# P02502134C

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Grand Hall factory part# P02502134C

Part Number: 03340
Weight: 0.5

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

10” Bamboo Skewers (100 pieces)

• Ideal for grilling meat and vegetables
• Soak skewers in water about 1/2 hour before using
• Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
• Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.

Part Number: 11060
Weight: 0.6

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3