Igniter Components for Grand Hall grills

Igniter collector box, ceramic electrode with male spade connector, and mounting plate for some Grand Hall grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 02618
Dimensions: 4
Material: stainless steel
Weight: 0.3

electrode

For more information about ignition systems and components, please see article Ignition 101 in our help center for some Grand Hall grills.

Part Number: 02622
Dimensions: 3 1/4” x 1 1/2”
Material: ceramic
Weight: 0.1

Ignitor collector box with ceramic electrode and male round connector for some Grand Hall grills.

• Wire not included. Commonly used with wire part# 03400.
• Designed to connect to wires with round female connector.
• If used with existing wire, confirm connector type is round where wire connects to electrode.

See part 02623-X4 for a more econimical 4 pack.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 02623
Material: ceramic
Weight: 0.2

Collector box with electrode and connector wire (both ends are female spade)

For more information about ignition systems and components, please see article Ignition 101 in our help center for some Grand Hall grills.

Part Number: 02624
Material: ceramic
Weight: 0.2

Ignition module switch for spark generators that accept wired remote (button) trigger switches for some Grand Hall grills. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Universal 5 1/2” jumper wire with female spade ends to close off unused pair of outlets in battery-powered spark generator, or use as an adaptor wire for some Grand Hall grills.
NOTICE: EACH END HAS A PLASTIC PROTECTOR CAP.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03197
Weight: 0.05

Universal 2 5/8” adapter wire with female round and male spade connectors for some Grand Hall grills. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory piezo spark generators have male round connectors, while battery operated electronic spark generators usually have male spade connectors.

• Can change male round to male spade
• Can change female spade to female round

ALL

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03198
Weight: 0.05

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover for some Grand Hall grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Universal battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has one (1) terminal (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03310
Weight: 0.3

Universal volt battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03320
Weight: 0.3

Universal battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03330
Weight: 0.5

Universal three-outlet battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03333
Dimensions: 2 9/16” x 2”
Weight: 0.5

Universal battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has (5) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03335
Dimensions: 2 5/8” x 2”
Weight: 0.3

Universal four-outlet battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Small AA battery powered push button spark generator for some Grand Hall grills.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03342
Weight: 0.3

Universal battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has six (6) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03350
Weight: 0.7

Burner mounted replacement electrode for use with burner 15641 for some Grand Hall grills.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch for some Grand Hall grills.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Universal battery powered push button ignitor for some Grand Hall grills.

• 1.5 volt
• Has five (5) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03380
Dimensions: 3 5/16” x 2”
Weight: 0.7

25” wire with female spade connector on one end, and female round connector on the other end for some Grand Hall grills. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors) for some Grand Hall grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

Ignition connection wire used to connect battery powered spark generators to electrodes for some Grand Hall grills. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors for some Grand Hall grills. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator for some Grand Hall grills. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

20” Ignitor adapter wire with female spade connector and male round connector for some Grand Hall grills. Used primarily on Ducane models 7100 and 7200 to extend the wire from the 03758 collector box and electrode to the electronic spark generator (igniter).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03750
Dimensions: 1/16
Weight: 0.05

Universal adapter wire with male round and female spade connectors for some Grand Hall grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03751
Weight: 0.05

Collector box and ceramic electrode with male spade connector for some Grand Hall grills. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, but no ground wire, see ground wire 03620.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03800
Material: ceramic
Weight: 0.2

Collector box and electrode assembly for some Grand Hall grills. Tongue style burner mounted collector box with ceramic electrode, 15” wire, and female round connector. Not designed to mount on original equipment burners. Fits our stainless steel burners with special mounting bracket only. Will NOT fit on cast iron burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03900
Material: ceramic
Weight: 0.2

Burner mounted electrode with male spade connector for some Grand Hall grills. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Part Number: 04010
Material: ceramic
Weight: 0.05

Universal collector box with electrode and wire for some Grand Hall grills. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

46” Wire with female spade connectors and square plastic connectors for some Grand Hall grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Battery powered push button igniter for some Grand Hall grills.

• Has two (2) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB2-B
Weight: 0.3

Battery powered push button igniter for some Grand Hall grills.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB4-B
Weight: 0.3

Push-button electronic igniter with two (2) spade connectors for some Grand Hall grills. Black cap. 1 AAA battery (not included).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG2006
Weight: 0.2

Push-button electronic igniter with four (4) spade connectors for some Grand Hall grills. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

Universal 3 outlet rotary spark generator for some Grand Hall grills. Includes knob.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-8B
Weight: 0.3