Model: 7000H

Replacement stainless steel burner. Includes venturi mounting bolts/screws. Venturi not included, sold separately.

NOTE: The original cast brass and cast iron burners are no longer available. This replacement stainless steel version is slightly smaller, but supports the same amount of gas with good heat distribution. The stainless steel version will not screw down into the base of the grill, but simply sits in the bottom of the grill using adjustable support brackets, which are included.

Part Number: AZ001504-SS
Material: stainless steel
Weight: 2.5
Dimensions: 15 7/8” x 8”

AZ001504-R Replacement cast iron burner. Includes venturi mounting bolts. Venturi not included, sold separately. Replaces original Great Outdoors part# AZ001504.

Fits models:

• 5500
• 6000
• 6100
• 7000
• 7500

NOTE: The original Great Outdoors cast brass and cast iron burners are no longer available. This replacement burner is slightly larger, but fully functional. It's ”legs” are not threaded, so it simply sits in the bottom of the grill.

Part Number: AZ001504-R
Material: cast iron
Weight: 7.0
Dimensions: 15 1/2” x 8”

Universal Spider Guards. Helps prevent dangerous flashback fires caused by spider webs in venturi tubes.Stainless steel spider guards slip over the air shutter on most venturi tubes to help keep the spiders out. For 3/4” venturi tubes.

Part Number: SG-B
Material: stainless steel
Weight: 0.1

AZ000505-R Replacement venturi tube. Includes gasket and screws. Replaces original Great Outdoors part# AZ000505.

Fits models:

• 6000
• 6100
• 7000
• 7500

Part Number: AZ000505-R
Material: zinc plated steel
Weight: 0.7
Dimensions: 2 15/16” x 4 1/8”

Cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of two (2).

Part Number: 61602
Material: matte cast iron
Weight: 12.8
Dimensions:

• Front-To-Back: 14 3/4″
• Side-To_Side: 23 1/2″

Stainless Steel cooking grid.

• Made in USA
• Solid 1/4” 304 stainless rods
• Each panel measures 15” x 11 3/8”

Part Number: CG-12SS
Material: stainless steel
Weight: 3.40
Dimensions:

• Front-To-Back: 15″
• Side-To_Side: 11 3/8″

Stainless Steel cooking grids. SET OF TWO (2) panels.

• Made in USA
• Solid 1/4” 304 stainless rods
• Each panel measures 15” x 11 3/8”
• Overall dimensions: 18 1/4” x 22 3/4”

Replaces Great Outdoors factory part# AF000105

Part Number: CG-12SS-X2
Material: stainless steel
Weight: 6.8
Dimensions:

• Front-To-Back: 15″
• Side-To_Side: 22 3/4″

carbon steel rock grate for Great Outdoors model 7000H.

Replaces Great Outdoors factory part# AF000205

Part Number: 91701
Material: steel wire
Weight: 5.2
Dimensions:

• Front-To-Back: 12 3/4″
• Side-To_Side: 20″

Heat Shield. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Great Outdoors factory part# AI000204

Part Number: CLA-MS0067
Material: stainless steel
Weight: 1.4
Dimensions:

• Front-To-Back: 10 1/4″
• Side-To_Side: 16 3/8″

Genuine OEM 21” wire for side burner or other applications. One female spade connector, one female round connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 10342-T14
Weight: 0.05
Dimensions: 21

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal collector box with electrode and wire. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

Collector box and ceramic electrode with male spade connector. Will not work with original wire, which is attached directly to the original electrode. Requires two (2) 03400 wires with female spade connectors. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, no wire.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Great Outdoors factory part# AN000103

Part Number: 03800
Material: ceramic
Weight: 0.2

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Great Outdoors factory part# AN000203

Part Number: 03400
Weight: 0.1

Rotary piezo spark generator. Two round connector leads send spark to both main burners. Use with two 03400 wires.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Great Outdoors factory part# AN000303

Part Number: 03220
Weight: 0.2

Premium quality polyester lined vinyl cover, E-Z on velcro tabs. For large grills, full length.

• 60” left to right
• 20” front to back
• 42” top to bottom

Please measure your grill to determine which cover fits best. Avoid too snug a fit as a slightly oversized cover is easier to take off and put back on.

Part Number: CV-4PREM
Material: Vinyl
Weight: 3.5

Silver plastic control knob. Replaces original part# 50002552. Can also be used to replace knob part# AZ000703.

• Off position D-Value: 6 o'clock
• Knob diameter: 2 3/16”
• Socket diameter: 8mm
• Knob shaft: None

Part Number: 02552
Material: plastic
Weight: 0.1
Dimensions: 2 3/16” x 2 3/16”

24” LP hose with QCC-1 type one regulator. For use on ”new style” tanks. Use with 34100 twin manifold.

Part Number: 80012
Weight: 0.80
Dimensions: 23 1/2” x 0 1/2”

Premium quality stainless steel warming rack. You simply can't buy a better quality warming rack than this, which weighs in at almost 5lbs of solid 304 grade stainless steel. This super heavy-duty warming rack was made to replace AF000303, the porcelain coated steel racks found on BBQ grills made by The Great Outdoors Grill Company, but can fit in any grill with 23 inches or more for the rack to sit on.

• Far superior to the original porcelain coated steel rack
• Rests on your existing cooking grids.
• Solid 1/4” 304 stainless steel rods.
• Stands 3 inches tall.
• Made in USA .

WARNING: Before ordering this universal rack, please verify your grill has enough space to accomodate it. At least 23” inside the closed lid is required.

Replaces Great Outdoors factory part# AF000303

Part Number: AF000303-SS
Material: stainless steel
Weight: 4.8
Dimensions:

• Front-To-Back: 6 1/4″
• Side-To_Side: 22 3/4″

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

Bamboo Appetizer 7” Skewers - pack of eight. Limited to supplies on hand.

Part Number: 11040
Weight: 0.4
Dimensions: 7

Ceramic briquette. Briquettes collect heat and radiate it to the food on the cooking grids. They also help prevent flare-ups and keep the flames from actually touching the food allowing for more efficient and uniform heat distribution.

Designed primarily to work in stainless steel trays on Lynx, Alfresco, and other brand grills, these briquettes can be and often are used on any grill with an ordinary grate to support them.

• Individual briquettes measure 2” x 2”
• Set includes 28 ceramic briquettes
• More than one set may be required per grill model

Part Number: BQLYX
Material: ceramic
Weight: 4.0
Dimensions: 2” x 2”

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Material: stainless steel
Weight: 0.5
Dimensions: 8 1/4

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Porcelain Coated Square Wok Topper.
12” x 12” x 2” porcelain coated grilling wok with stainless steel handles and perforations. The single draw design improves functionality and rigidity, it also makes it much easier to clean.

Part Number: 98121
Material: porcelain steel
Weight: 1.6

Extra Wide Nylon Grill Brush

Brush anywhere on the grill, deep into the corners, between the grids, and in broad strokes along the surface. The triangular shaped head of this brush is ideal for cleaning anywhere. 17 in. overall length with a 6. in. wide head. Nylon bristles, wire shaft and resin handle.

*For use on a cool grill.

Part Number: 77643
Weight: 0.5