Kenmore 122.33492410

Porcelain steel Flame Tamer. Sold individually.

Part Number: 97371
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 0.55

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.16

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.88

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
WARNING: This is the stainless steel version of 97371. The parts have the same dimensions except this version has a ”height” that is 3/16” taller than 97371. Determine if this matters to you and order the part that best replaces your old heat plate.

Part Number: CLA-TS0157
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 0.72

Porcelain steel Flame Tamers. SET OF SIX.

Part Number: 97371-6X
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 3.3

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Heat indicator with a single probe and requires a 5/16” mounting hole. Note, the back side DOES NOT have an alignment pin.

Part Number: 00021
Dimensions: 3 5/8” x 1 3/4”
Weight: 0.2

6 chrome plated 18” shish-ke-bab skewers

Part Number: 63371
Weight: 0.2

20” Professional Extra Long Tong.
20” Stainless steel tong with red soft grip rubber inserts. Grip your food on the grill with ease. Manual lock saves on storage space.

Part Number: 40269
Material: stainless steel
Weight: 0.14

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Deluxe non-stick chicken and rib tumble basket. Attaches to rotisserie spit rod.

• Ideal for cooking pieces of meat or vegetables
• Self basting, easy to use
• Locks on spit rod with thumb screw (supplied)
• 6 1/2” x 10” long

Part Number: 24764
Dimensions: 6 1/2” x 10”
Weight: 1.1

Grill Mitt With Neoprene Palm.

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most

Part Number: 90963
Weight: 0.5