Home > Kenmore Grill Models > Kenmore 16167
Char-Broil Performance T-46D LP gas BBQ grill
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Kenmore grill.
Replacement grill parts for the Kenmore 16167 (Performance T-46D)
Stainless steel burner for Kenmore model 16167.
Part Number: 14841
Material: stainless steel
Weight: 0.5
Dimensions: 14 7/16” x 1”
Stainless steel cross-over burner shown in inches and millimeters for Kenmore model 16167.
Part Number: 05592
Material: stainless steel
Weight: 0.1
Dimensions: 6 3/8” x 0 13/16”
Reversible, heavy cast iron
cooking grids.
Porcelain treated, flat matte finish. SOLD INDIVIDUALLY
Part Number: 66652-1PC
Material: matte cast iron
Weight: 10.0
Dimensions:
- Front-To-Back: 18 1/4″
- Side-To_Side: 13 1/8″
$119.95
$63.28
Premium universal cooking grids. Set of two (2) grids. Porcelain treated cast iron. Matte finish.
Each panel measures:- Front-to-Back: 18 1/4”
- Side-to-Side: 13 1/8”
Total Side-to-Side: 26 1/4”
Part Number: 66652-UNI-X2
Material: cast iron
Weight: 18.8
Dimensions:
- Front-To-Back: 18 1/4″
- Side-To_Side: 26 1/4″
Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 66652-UNI-X2 for a set of two (2) grids.
Part Number: 66652-UNI
Material: cast iron
Weight: 9.4
Dimensions:
- Front-To-Back: 18 1/4″
- Side-To_Side: 13 1/8″
Stamped stainless steel
cooking grids (set of 3). Each grid is a grid-in-tray assembly, so there is actually a total of 6 pieces.
Part Number: 5S483
Material: stamped stainless steel
Weight: 15.4
Dimensions:
- Front-To-Back: 18 7/16″
- Side-To_Side: 26 5/8″
Reversible, heavy cast iron
cooking grids.
Porcelain treated, flat matte finish. Sold as a set of two (2).
Part Number: 66652
Material: matte cast iron
Weight: 19.35
Dimensions:
- Front-To-Back: 18 1/4″
- Side-To_Side: 26 1/4″
$194.85
$119.99
Stamped stainless steel
cooking grids. SOLD AS A SET OF THREE (3) PIECES ONLY.
WARNING: This
cooking grid set does not include the bottom trays. For the grid in tray set see part # 5S483.
Replaces Kenmore factory part# G519-A400-W1
Part Number: 5S473
Material: stamped stainless steel
Weight: 8.0
Dimensions:
- Front-To-Back: 18 7/16″
- Side-To_Side: 26 5/8″
SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA

.
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0141-X4
Material: stainless steel
Weight: 3.92
Dimensions:
- Front-To-Back: 16″
- Side-To_Side: 3 3/4″
Flame Tamer, stainless steel. Made in USA

.
NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0141
Material: stainless steel
Weight: 0.98
Dimensions:
- Front-To-Back: 16″
- Side-To_Side: 3 3/4″
Stainless steel aftermarket Flame Tamer
heat plate.
- Stainless equivalent of part 93321
- Superior to the porcelain steel originals
- Rust and corrosion restitant
- Sold individually
- Made in USA

Part Number: 93321-SS
Material: stainless steel
Weight: 0.7
Dimensions:
- Front-To-Back: 16″
- Side-To_Side: 3 3/4″
Stainless steel
heat plate/Flame Tamer for Kenmore model 16167.
Part Number: CBHP2
Material: stainless steel
Weight: 0.7
Dimensions:
- Front-To-Back: 16″
- Side-To_Side: 3 3/4″
Electrode, gas collector box, and wire. The connecting wire has a flat female
spade connector, which is typically used with electronic (battery operated) ignitors (see
Ignition 101 in our help center).
NOTE: This electrode is also sometimes used with push-button or rotary
piezo ignitors, such as our part#
03100 and
03120, which have
round connectors. When connecting 01472 electrode to ignitors with
round connectors, use short wire part#
03199C to convert the electrode wire from a femal
spade connector to a female
round connector.
Part Number: 01472
Material: ceramic
Weight: 0.1
Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03152
Weight: 0.1
Dimensions: 17 3/4” x 1”
Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.
Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part
03621. Inspect your system.
- 1.5 volt
- Has five (5) spark outlets (male spade connector)
- Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
- Uses a single AA battery (not included)
- Requires 7/8” mounting hole
- Overall dimensions: 2” x 3 3/8” x 2 5/8”
NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03352
Weight: 0.7
Dimensions: 3 3/8” x 2”
Universal 2 1/2” adaptor wire with a round female end and a male spade end.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IG-46B
Weight: 0.10
Dimensions: 2 1/2
Semi-circular, snap in heat indicator with 2 3/4” heat prob for Kenmore model 16167.
Part Number: 00473
Material: stainless steel
Weight: 0.1
Dimensions: 1 3/4” x 1 3/16”
6 chrome plated 18” shish-ke-bab skewers
Part Number: 63371
Weight: 0.2
2 in 1 chrome plated turner / tong with PVC coated handle
Part Number: 40730
Material: chrome steel
Weight: 0.6
Dimensions: 14
Marinade Injector.For injecting flavor and marinades into meat. Great for use with chicken, beef, pork, lamb etc. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber. Easy to use and clean.
Part Number: 14950
Material: stailess steel
Weight: 0.5
Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.
Part Number: 24785
Weight: 1.5
Dimensions: 7 1/2” x 16”
Grill Mitt With Neoprene Palm. 16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most
Part Number: 90963
Weight: 0.2
|
Kenmore grill model 16167. Some parts not specific to a grill brand or model like regulators, posts, and heat indicators, which are listed in our repair parts section. 02-Nov-26
|
We ship Kenmore BBQ parts worldwide
Back to Kenmore grill parts