Home > Kenmore Grill Models > Kenmore 415.16943010Kenmore 4-Burner LP gas outdoor BBQ grill with side burner
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Kenmore grill.
Replacement BBQ grill parts for Kenmore model: 415.16943010
415.16943010 Burners
Stainless steel burner for Kenmore model 415.16943010.
Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5
$33.83
Stainless steel burner for Kenmore model 415.16943010.
Replaces Kenmore factory part# G515-2200-W1
Part Number: CBP5
Dimensions: 15 7/8” x 1”
Material: stainless steel
Weight: 1.0
$33.83
415.16943010 Burner Brackets and Carryovers
stainless steel cross-over burner for Kenmore model 415.16943010.
Part Number: 05592
Dimensions: 6 3/8” x 0 13/16”
Material: stainless steel
Weight: 0.1
$14.85
415.16943010 Cooking Grids
Stainless Steel
cooking grids. SET OF TWO (2) panels.
- Made in USA
- Solid 5/16” 304 stainless rods
- Each panel measures 18 1/2” x 12 3/4”
- Overall dimensions: 18 1/2” x 25 1/2”
Part Number: CG-109SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 15.0
$204.95
Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids.
- Made in USA
- Commercial grade 304 stainless steel
- 5/16” solid stainless rods
- Sold as a set of two (2).
Each panel measures:- Front-to-Back: 18 1/2”
- Side-to-Side: 12 3/4”
Total Side-to-Side: 25 1/2”Part Number: 54712-SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 5.0
$204.95
Premium quality stainless steel
cooking grid. Far superior to the porcelain coated steel grids it replaces.
- Made in USA
- 304 commercial grade stainless steel
- Solid 5/16” diameter solid stainless rods
- Sold individually
Fits grills made by Charbroil, Kenmore, Master Chef and others.
Part Number: 54712-SS
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 12 3/4”
Weight: 2.5
$104.85
415.16943010 Flame Tamers
Porcelain steel Flame Tamer. Sold individually.
Part Number: 94491
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: porcelain steel
Weight: 1.1
$30.73 $21.99
Stainless steel aftermarket Flame Tamer.
- Stainless equivalent of part 94491
- Superior to the porcelain steel originals
- Rust and corrosion restitant
- Sold individually
- Made in USA
Part Number: 94491-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: stainless steel
Weight: 0.7
$37.49
415.16943010 Igniter Components
Electrode, gas collector box, and wire. The connecting wire has a flat female
spade connector, which is typically used with electronic (battery operated) ignitors (see
Ignition 101 in our help center).
NOTE: This electrode is also sometimes used with push-button or rotary
piezo ignitors, such as our part#
03100 and
03120, which have
round connectors. When connecting 01472 electrode to ignitors with
round connectors, use short wire part#
03199C to convert the electrode wire from a femal
spade connector to a female
round connector.
Part Number: 01472
Material: ceramic
Weight: 0.1
$10.87
Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.
Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part
03621. Inspect your system.
- 1.5 volt
- Has five (5) spark outlets (male spade connector)
- Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
- Uses a single AA battery (not included)
- Requires 7/8” mounting hole
- Overall dimensions: 2” x 3 3/8” x 2 5/8”
NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7
$39.89
Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1
$19.80
Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03199C
Weight: 0.05
$4.37
415.16943010 Accessories
Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.
Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90
$25.40
16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.
Part Number: 40240
Material: chrome steel
Weight: 0.9
$16.59
Deluxe 13” basting mop with hardwood handle and cotton mop head.
Part Number: 42055
Dimensions: 13
Weight: 0.2
$8.76
Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.
Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5
$22.60
Replacement heads for grill brush 77600. Set of two.
Part Number: 77650
Weight: 0.3
$6.73