Igniter Components for PGS grills

Universal 5 1/2” jumper wire with female spade ends to close off unused pair of outlets in battery-powered spark generator, or use as an adaptor wire for some PGS grills.
NOTICE: EACH END HAS A PLASTIC PROTECTOR CAP.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03197
Weight: 0.05

Universal 2 5/8” adapter wire with female round and male spade connectors for some PGS grills. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory piezo spark generators have male round connectors, while battery operated electronic spark generators usually have male spade connectors.

• Can change male round to male spade
• Can change female spade to female round

ALL

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03198
Weight: 0.05

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover for some PGS grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Battery powered push button spark generator with single round connector for some PGS grills.

• Installs behind the control panel, replacing a piezo plunger.
• Fits most grills that use a push-button piezo plunger.
• Uses a single AA battery (not included).
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03300
Dimensions: 2 7/8” x 2 1/16”
Weight: 0.3

Universal battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has one (1) terminal (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03310
Weight: 0.3

Universal volt battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03320
Weight: 0.3

Universal battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03330
Weight: 0.5

Universal three-outlet battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03333
Dimensions: 2 9/16” x 2”
Weight: 0.5

Universal battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has (5) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03335
Dimensions: 2 5/8” x 2”
Weight: 0.3

Universal four-outlet battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Universal battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has six (6) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03350
Weight: 0.7

Universal battery powered push button ignitor for some PGS grills.

• 1.5 volt
• Has five (5) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03380
Dimensions: 3 5/16” x 2”
Weight: 0.7

25” wire with female spade connector on one end, and female round connector on the other end for some PGS grills. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors) for some PGS grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

14” ground wire with female spade connector and eye connectors for some PGS grills. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

20” Ignitor adapter wire with female spade connector and male round connector for some PGS grills. Used primarily on Ducane models 7100 and 7200 to extend the wire from the 03758 collector box and electrode to the electronic spark generator (igniter).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03750
Dimensions: 1/16
Weight: 0.05

Universal adapter wire with male round and female spade connectors for some PGS grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03751
Weight: 0.05

Collector box and ceramic electrode with male spade connector for some PGS grills. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, but no ground wire, see ground wire 03620.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03800
Material: ceramic
Weight: 0.2

Collector box and electrode assembly for some PGS grills. Tongue style burner mounted collector box with ceramic electrode, 15” wire, and female round connector. Not designed to mount on original equipment burners. Fits our stainless steel burners with special mounting bracket only. Will NOT fit on cast iron burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03900
Material: ceramic
Weight: 0.2

Single outlet electronic ignitor for some PGS grills. For 2005 models JNR, WNK, TJK.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: GG-EIB
Weight: 0.2

12” igniter connecting wire for battery-operated electronic igniters for some PGS grills. Female spade connector on one end connects to igniter, female spade connector on the other end connects to electrode. Fits JNR, WNK, and TJK grill models equipped with electronic igniters. (Part numbers GG-ERIW and KK-IW are the same.)

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: GG-ERIW
Weight: 0.3

Ignitor Box Assembly for Grill Replacement Parts for JNR, WNK, TJK

For more information about ignition systems and components, please see article Ignition 101 in our help center for some PGS grills.

Part Number: GG-IB
Weight: 0.2

Universal collector box with electrode and wire for some PGS grills. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

46” Wire with female spade connectors and square plastic connectors for some PGS grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Tongue style collector box for burner mounted applications for some PGS grills. Includes preinstalled electrode with round female connector end and 20” wire. Fits on all of our Deluxe stainless H burners (LB, SB, DLB, DSB) using special mounting bracket on these burners. Will not fit on cast iron burners (see part IG-15B for cast iron burner applications).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-5B
Weight: 0.3

Battery powered push button igniter for some PGS grills.

• Has two (2) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB2-B
Weight: 0.3

Push-button electronic igniter with two (2) spade connectors for some PGS grills. Black cap. 1 AAA battery (not included).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG2006
Weight: 0.2

Universal 3 outlet rotary spark generator for some PGS grills. Includes knob.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-8B
Weight: 0.3