Home > Sams Grill Models > Sams Y0660NG-1
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Sams grill.
Replacement grill parts for the Sams Y0660NG-1
Y0660NG-1 Burners
Cast iron burner for Sams model Y0660NG-1.
Part Number: 29251
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 6.4
$39.97
Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..
Part Number: 29251-CSS-X3
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 10.05
$258.70
Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..
Part Number: 29251-CSS
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 3.35
$86.68
Cast iron burners. SET OF THREE(3).
Part Number: 29251-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 19.2
$101.84
Cast iron burner for Sams model Y0660NG-1.
Part Number: CISC-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 15.0
$92.94
Y0660NG-1 Burner Brackets and Carryovers
Stainless steel burner mounting bracket. Also called a cross over channel. Made in USA
.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Replaces Sams factory part# P0220408BA
Part Number: CLA-MS0032
Dimensions: 34 1/4
Material: stainless steel
Weight: 2.2
$45.33
Y0660NG-1 Flame Tamers
Ceramic Flame Tamers - Box of 6. Use with rack part# FP-P1736B; see
Rock Grates.
Tired of replacing broken ceramic flame tamers? For many models, you can replace them and the rack that holds them with our longer-lasting made-in-the-USA metal flame tamers, which come in stainless steel and more economical carbon steel versions. When available, the replacement metal flame tamers are shown with the other parts we have for a model.
Part Number: 97501
Dimension Front-to-Back: 8”
Dimension Side-to-Side: 7 1/4”
Material: ceramic
Weight: 9.0
$70.20
Replacement steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA
.
Part Number: CLA1721
Dimension Front-to-Back: 16 7/8”
Dimension Side-to-Side: 9 3/4”
Material: carbon steel
Weight: 3.5
$23.22
Stainless steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA
.
Part Number: CLA2721
Dimension Front-to-Back: 16 3/4”
Dimension Side-to-Side: 9 3/4”
Material: stainless steel
Weight: 2.4
$49.99
Y0660NG-1 Igniter Components
Battery powered push button igniter.
- Has four (4) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IGEIB4-B
Weight: 0.3
$31.52
Universal four-outlet battery powered push button ignitor.
- 1.5 volt
- Has four (4) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03340
Weight: 0.5
$31.50
Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
See part 03610-X4 for a more economical 4-pack.
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
$8.67
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
$6.58
Collector box with electrode and connector wire (both ends are female spade)
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Sams factory part# P2652A
Part Number: 02624
Material: ceramic
Weight: 0.2
$11.86
Push-button electronic igniter with four (4)
spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG4010
Weight: 0.2
$18.48
Y0660NG-1 Knobs and Handles
Black control knob to fit Sam's models for Sams model Y0660NG-1.
Part Number: 03430
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.2
$10.87
Y0660NG-1 Valves, Orifices, and Manifolds
Clamp-on brass gas valve with straight outlet. Includes orifice.
- D-Value: 12 o'clock
- Stem diameter: 6mm
- Stem length: 1 3/4”
Includes orifice with #72
starter hole. Must be drilled to proper
drill size.
Part Number: 3700C
Dimensions: 4 15/16” x 2 1/8”
Material: brass
Weight: 0.5
$28.09
Neoprene valve gasket for clamp-on gas control valves. 19mm.
Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01
$3.25
Brass orifice. 6mm x 3/4” cone shaped orifice with #64
drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper
drill size.
If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.
Part Number: 31400
Dimensions: 0 3/4” x 0 5/16”
Material: brass
Weight: 0.01
$7.45
Brass long blunt-end
hood orifice drilled to #64
starter hole. Fits valve 3042C, others. Must be drilled to proper
drill size.
If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.
Part Number: 31800
Dimensions: 1 5/16” x 0 9/16”
Material: brass
Weight: 0.1
$10.14
Y0660NG-1 Accessories
10” Bamboo Skewers (100 pieces)
- Ideal for grilling meat and vegetables
- Soak skewers in water about 1/2 hour before using
- Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
- Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.
Part Number: 11060
Weight: 0.6
$4.09
16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.
Part Number: 40240
Material: chrome steel
Weight: 0.9
$16.59
Deluxe 13” basting mop with hardwood handle and cotton mop head.
Part Number: 42055
Dimensions: 13
Weight: 0.2
$8.76
Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.
Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5
$22.60
Replacement heads for grill brush 77600. Set of two.
Part Number: 77650
Weight: 0.3
$6.73