DCS DCS27-BQRL

304 Stainless steel 15,000 BTU infrared rotissierie burner. For use with both liquid propane (LP) and natural gas grills. Orifice not included. Use old orifice or purchase our orifice part# CLA-VL0251 for LP, or part# CLA-VB0246 for natural gas applications.

Dimensions:

• Maximum overall length, including mounting tab on one end: 20 7/8”
• Maximum width: 3 3/8”

Replaces DCS factory part# DCS-210357

Part Number: CLA-BS0250
Dimensions: 3 3/8” x 20”
Material: stainless steel and ceramic
Weight: 3.50

210358-R BURNER -27BBQ MAT PORC.
Cast iron replacement ”H” burner. Fits older DCS 27” grills.

Replaces original DCS burner part# 210358.

NOTE: Also fits grills manufactured by Dynamic Cooking Systems (DCS) for other brands.

Air shutter included.

Part Number: DCS-210358-R1
Dimensions: 16” x 6 1/4”
Material: cast iron
Weight: 10.9

212425-SSHeavy duty stainless steel grill rack. Fits DCS27 and DCS27A Professional Series gas grills by Dynamic Cooking Systems. Sometimes referred to as GRILL RACK - 27 BBQ.

• Replaces DCS factory part# 212425.
• Large diameter 5/16” stainless steel rods.
• Commercial grade 304 stainless steel.
• Sold individally.

Part Number: DCS-212425-SS
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 12 3/4”
Weight: 1.0

213524-R LAVA ROCK SUPP,27BQ.
Stainless steel Lava Rock support. This is a rack/tray for holding Lava Rock (not included). Requires one per burner.

Fits DCS 27” DCS27 and DCS27A Professional Series grills by Fisher & Paykel. These grills have the smaller 16” cast iron H burners.

• Replaces original DCS part# 30709-020.
• See part# 210005-R for Lava Rock.
• Sometimes shipped with vinyl peel-off coating. Remove before use.
• Made in USA
• Sold individually.

Part Number: DCS-213524-R
Dimensions: 16 1/2” x 10 5/8”
Material: stainless steel
Weight: 2.2

210005-R LAVA ROCK.
Natural lava rock processed and screened for uniformity. For use with Support Rack/Radient 213524 and 213949.

NOTE: This is NOT a DCS product. The original DCS part was 4 pounds of Lava Rock. This is a 7lb bag manufactured by GrillPro.

Part Number: DCS-210005-R
Material: pumice
Weight: 7.5

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Push-Button self-grounding piezo spark generator. Has round male connector, so connecting wire needs to be female round connector. If needed, see part# 03199C for a short adapter wire that converts flat female spade connectors to female round. For more information, see our help center article Ignition 101.

Replaces DCS factory part# DCS-211551P

Part Number: 03100
Weight: 0.1

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

24” LP hose and regulator with QCC-1 connection.

• For use on ”new style” QCC-1 tanks.
• Consists of hose part# 01000 and regulator part# 00920.
• Hose end with SAE 3/8” female flare fitting connects to grill.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. See our flare fitting description for information on measuring and sizes.

Replaces DCS factory part# DCS-210753

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

Brass valve for DCS.

• For LP and natural gas grills (see below)
• Off position D-Value: 12 o'clock
• Stem diameter: 8mm
• Orifice not included

NOTE: There is a set screw in the stem that allows this valve to be used in both LP or natural gas grills. The valve is shipped with the screw set in LP position. Turn the screw counterclockwise about seven turns for natural gas use.

Replaces DCS factory part# DCS-210733

Part Number: 30171
Dimensions: 3 7/16” x 1 5/16”
Material: brass
Weight: 0.3

#55 orifice for infrared burners use on natural Gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VB0246
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

#59 brass orifice for rotisserie burner. Fits liquid propane (LP) gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VL0251
Material: brass
Weight: 0.15

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3