Member's Mark Y0660LP

Cast iron burner for Member's Mark model Y0660LP.

Part Number: 29251
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 6.4

Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..

Part Number: 29251-CSS-X3
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 10.05

Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..

Part Number: 29251-CSS
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 3.35

Cast iron burners. SET OF THREE(3).

Part Number: 29251-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 19.2

Cast iron burner for Member's Mark model Y0660LP.

Part Number: CISC-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 15.0

Stainless steel burner mounting bracket. Also called a cross over channel. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Members Mark factory part# P0220408BA

Part Number: CLA-MS0032
Dimensions: 34 1/4
Material: stainless steel
Weight: 2.2

Cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of three (3).

Part Number: 68073
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 31 11/16”
Material: matte cast iron
Weight: 19.2

Cast iron cooking grid. Porcelain treated, matte finish. Sold individually, number required varies by grill model.

Part Number: CG-71P-CI
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 7 5/8”
Material: cast iron
Weight: 5.55

Aftermarket reversible heavy cast iron cooking grid.

• Sold individually
• Number required varies, check your grill
• Porcelain treated, flat matte finish
• Pointed side is designed for perfect sear marks
• Grooved side captures juices for continous basting

Fits: Broil King 500/625/750 series grills.

NOTE: This aftermarket part, made of the same materials as the original, is a perfect replacement for original part# 22005-281 but at a much lower cost.

Part Number: 22005-281-R
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 6 1/16”
Material: Cast iron
Weight: 5.0

Porcelain steel cooking grid. Porcelain enameled, glossy finish. Sold individually.

Part Number: 51631
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 5/16”
Material: porcelain steel wire
Weight: 4.0

Porcelain steel cooking grids. Porcelain enameled, glossy finish. Sold as a set of three (3). If you prefer a heavier cast iron porcelain enameled glossy finish cooking grid, select four (4) panels of # 65131.

Part Number: 54453
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 31 1/2”
Material: porcelain steel wire
Weight: 15.10

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually.

Part Number: 65131-UNI
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 7 5/8”
Material: cast iron
Weight: 5.55

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually, number required varies, check your grill.

Part Number: 67845-1PC
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 6 1/16”
Material: matte cast iron
Weight: 5.5

Cast iron cooking grids, porcelain treated, flat matte finish for Member's Mark model Y0660LP.

Part Number: 67845
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 30 5/16”
Material: matte cast iron
Weight: 27.2

Premium universal cooking grids. Set of three (3) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 18 7/8”
• Side-to-Side: 10 1/2”

Total Side-to-Side: 31 1/2”

Part Number: 68073-UNI-X3
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 31 1/2”
Material: cast iron
Weight: 21.75

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 68073-UNI-X3 for a set of three (3) grids.

Part Number: 68073-UNI
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 10 1/2”
Material: cast iron
Weight: 7.25

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually.

Part Number: 69501
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 1/8”
Material: cast iron
Weight: 4.85

Ceramic Flame Tamers - Box of 6. Use with rack part# FP-P1736B; see Rock Grates.

Tired of replacing broken ceramic flame tamers? For many models, you can replace them and the rack that holds them with our longer-lasting made-in-the-USA metal flame tamers, which come in stainless steel and more economical carbon steel versions. When available, the replacement metal flame tamers are shown with the other parts we have for a model.

Part Number: 97501
Dimension Front-to-Back: 8”
Dimension Side-to-Side: 7 1/4”
Material: ceramic
Weight: 9.0

Replacement steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA .

Part Number: CLA1721
Dimension Front-to-Back: 16 7/8”
Dimension Side-to-Side: 9 3/4”
Material: carbon steel
Weight: 3.5

Stainless steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA .

Part Number: CLA2721
Dimension Front-to-Back: 16 3/4”
Dimension Side-to-Side: 9 3/4”
Material: stainless steel
Weight: 2.4

Ceramic Flame Tamer. Measures 7” x 8”. Box of 6.

Note: This part is used in racks P1736B, P1739A, P01722021B.

Fits models:

• Y0005XC-1
• Y0005XC-2
• Y0101XC
• Y0202XC
• Y0660LP/NG
• And others

Replaces Members Mark factory part# P1736A

Part Number: P1736A-R
Dimension Front-to-Back: 7”
Dimension Side-to-Side: 8”
Material: ceramic
Weight: 12.0

Rack for ceramic Flame Tamers; nickel plated heavy duty wire 5/16” thick. Uses 12 ceramic flame tamers part# P1736A-R (not included).

NOTE: This replacement part is not exactly like the original P1739A rack, but a very functional replacement. It cannot use the original ceramic Flame Tamers. The original rack held six larger Flame Tamers, while P01720021B-R uses twelve smaller ones. Using only 10 tamers will allow the smoker burner to remain uncovered as was the case with the original rack.

Replaces Members Mark factory part# P1739A

Part Number: P1739A-R
Dimension Front-to-Back: 17 1/4”
Dimension Side-to-Side: 33 7/16”
Material: nickel plated steel
Weight: 8.95

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Collector box with electrode and connector wire (both ends are female spade)

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Members Mark factory part# P2623D

Part Number: 02624
Material: ceramic
Weight: 0.2

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

Black control knob (Some originals may have been chrome).

• Off position D-Value: 12 o'clock
• Knob diameter: 2 3/16”
• Socket diameter: 6mm
• Knob shaft: None

Part Number: 03430
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.2

Clamp-on brass gas valve with straight outlet. Includes orifice.

• D-Value: 12 o'clock
• Stem diameter: 6mm
• Stem length: 1 3/4”

Includes orifice with #72 starter hole. Must be drilled to proper drill size.

Part Number: 3700C
Dimensions: 4 15/16” x 2 1/8”
Material: brass
Weight: 0.5

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

Brass orifice. 6mm x 3/4” cone shaped orifice with #64 drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper drill size.

If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.

Part Number: 31400
Dimensions: 0 3/4” x 0 5/16”
Material: brass
Weight: 0.01

Brass long blunt-end hood orifice drilled to #64 starter hole. Fits valve 3042C, others. Must be drilled to proper drill size.

If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.

Part Number: 31800
Dimensions: 1 5/16” x 0 9/16”
Material: brass
Weight: 0.1

Skewers for part 92339 kebob tray.

Part Number: 11040
Weight: 0.4

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Aluminum foil grilling trays. Package of three.

• Heavy duty aluminum foil
• Re-usable
• Great for grilling delicate foods like fish and veggies

Part Number: 50426
Dimensions: 9” x 13”
Weight: 0.4

Deluxe venturi brush with 11” coil spring flexible shaft

Part Number: 77310
Weight: 0.3