Kenmore 141.157951

P1935A-R-X4 Cast iron burner set for some Kenmore 4-Burner grills. This aftermarket burner replaces original burner part# P1935A.

This a 4-pack of burners.

Part Number: P1935A-R-X4
Dimensions: 12 7/8” x 2 1/8”
Material: cast iron
Weight: 8.8

P1935A-R Cast iron burner for some Kenmore 3, 4, and 6 burner grills. This aftermarket burner replaces original burner part# P1935A.

Part Number: P1935A-R
Dimensions: 12 7/8” x 2 1/8”
Material: cast iron
Weight: 2.2

Stainless steel burner support bracket. Replaces OEM # P2218B. Made in USA

Part Number: CLA-MS0293
Dimensions: 1 3/8” x 23 13/16”
Material: stainless steel
Weight: 0.75

Premium quality stainless steel cooking grids. SET OF TWO (2). Far superior to the porcelain coated steel grids it replaces.

• Made in USA
• 304 commercial grade stainless steel
• .225 diameter solid stainless rods

• Each panel measures 16 1/2” x 11 1/4”
• Overall dimensions: 16 1/2” x 22 1/2”

.

Part Number: CG-51SS-X2
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 22 1/2”
Material: stainless steel
Weight: 7.0

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Replaces Kenmore factory part# P1648B

Part Number: 68252
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 22 3/4”
Material: gloss cast iron
Weight: 13.11

Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.

• Made in USA
• Commercial grade 304 stainless steel
• .225” solid stainless rods
• Sold as a set of two (2).

Each panel measures:

• Front-to-Back: 16 1/2”
• Side-to-Side: 11 1.4”

Total Side-to-Side: 22 1/2”

NOTE: Some ProChef grills this part replaces used a wider single-piece grid.

Part Number: 53502-SS-X2
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 22 1/2”
Material: stainless steel
Weight: 7.0

Premium stainless steel cooking grid. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.

• Made in USA
• Commercial grade 304 stainless steel
• .225” solid stainless rods
• Sold individually, 2 required.

Part Number: 53502-SS
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 11 1/4”
Material: stainless steel
Weight: 3.50

Stainless steel heat plate/ Flame Tamer.
Made in USA

Part Number: KENHP1
Dimension Front-to-Back: 13 1/8”
Dimension Side-to-Side: 10 9/16”
Material: stainless steel
Weight: 1.0

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0154-X3
Dimension Front-to-Back: 13 3/16”
Dimension Side-to-Side: 10 5/8”
Material: stainless steel
Weight: 5.76

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0154
Dimension Front-to-Back: 13 3/16”
Dimension Side-to-Side: 10 5/8”
Material: stainless steel
Weight: 1.92

Porcelain steel Flame Tamer. Sold individually.

Part Number: 97061
Dimension Front-to-Back: 13 1/8”
Dimension Side-to-Side: 10 9/16”
Material: porcelain steel
Weight: 4.9

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Igniter collector box, ceramic electrode with male spade connector, and mounting plate.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02605013C

Part Number: 02618
Dimensions: 4
Material: stainless steel
Weight: 0.3

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02502164C

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02502164C

Part Number: 03340
Weight: 0.5

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Black control knob to fit Kenmore models for Kenmore model 141.157951.

Replaces Kenmore factory part# P3409B

Part Number: 03430
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.2

Clamp-on brass gas valve with straight outlet. Includes orifice.

• D-Value: 12 o'clock
• Stem diameter: 6mm
• Stem length: 1 3/4”

Includes orifice with #72 starter hole. Must be drilled to proper drill size.

Replaces Kenmore factory part# P3297C

Part Number: 3700C
Dimensions: 4 15/16” x 2 1/8”
Material: brass
Weight: 0.5

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

Brass orifice. 6mm x 3/4” cone shaped orifice with #64 drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper drill size.

If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.

Part Number: 31400
Dimensions: 0 3/4” x 0 5/16”
Material: brass
Weight: 0.01

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3