Home > Kenmore Grill Models > Kenmore 141.165400
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Kenmore grill.
Replacement gas grill parts for Kenmore model: 141.165400
141.165400 Burners
Cast iron burner for Kenmore model 141.165400.
Replaces Kenmore factory part# P02001006C
Part Number: 29351
Material: cast iron
Weight: 2.2
Dimensions: 12 7/8” x 2 1/8”
141.165400 Cooking Grids
Premium quality stainless steel
cooking grids. SET OF TWO (2). Far superior to the porcelain coated steel grids it replaces.
- Made in USA

- 304 commercial grade stainless steel
- .225 diameter solid stainless rods
- Each panel measures 16 1/2” x 11 1/4”
- Overall dimensions: 16 1/2” x 22 1/2”
.
Part Number: CG-51SS-X2
Material: stainless steel
Weight: 7.0
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 1/2″
Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.
- Made in USA

- Commercial grade 304 stainless steel
- .225” solid stainless rods
- Sold as a set of two (2).
Each panel measures:- Front-to-Back: 16 1/2”
- Side-to-Side: 11 1.4”
Total Side-to-Side: 22 1/2”NOTE: Some ProChef grills this part replaces used a wider single-piece grid.
Part Number: 53502-SS-X2
Material: stainless steel
Weight: 7.0
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 1/2″
Premium stainless steel cooking grid. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.
- Made in USA

- Commercial grade 304 stainless steel
- .225” solid stainless rods
- Sold individually, 2 required.
Part Number: 53502-SS
Material: stainless steel
Weight: 3.50
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 11 1/4″
Cast iron
cooking grids (set of 2).
Porcelain enameled, glossy finish.
Part Number: 68252
Material: gloss cast iron
Weight: 13.11
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 3/4″
141.165400 Heat Plates
Stainless steel
heat plate/ Flame Tamer.
Made in USA
Replaces Kenmore factory part# P1733B
Part Number: KENHP1
Material: stainless steel
Weight: 1.0
Dimensions:
- Front-To-Back: 13 1/8″
- Side-To_Side: 10 9/16″
SET OF THREE/3 PACK Stainless steel
heat plate/Flame Tamer. Made in USA

.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0154-X3
Material: stainless steel
Weight: 5.76
Dimensions:
- Front-To-Back: 13 3/16″
- Side-To_Side: 10 5/8″
Stainless steel
heat plate/Flame Tamer. Made in USA

.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0154
Material: stainless steel
Weight: 1.92
Dimensions:
- Front-To-Back: 13 3/16″
- Side-To_Side: 10 5/8″
141.165400 Igniter Components
Igniter collector box, ceramic electrode with male
spade connector, and mounting plate.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02605013C
Part Number: 02618
Material: stainless steel
Weight: 0.3
Dimensions: 4
Battery powered push button igniter.
- Has four (4) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502164C
Part Number: IGEIB4-B
Weight: 0.3
Universal four-outlet battery powered push button ignitor.
- 1.5 volt
- Has four (4) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502164C
Part Number: 03340
Weight: 0.5
Push-button electronic igniter with four (4)
spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG4010
Weight: 0.2
46” Wire with female
spade connectors and square plastic connectors.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IG-30B
Weight: 0.1
Dimensions: 46
Ignition connection wire used to connect battery powered spark generators to electrodes. One 46” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
141.165400 Knobs and Handles
Black control knob to fit Kenmore models for Kenmore model 141.165400.
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive Nov 6th.
Replaces Kenmore factory part# P03412331C
Part Number: 03430
Material: plastic
Weight: 0.2
Dimensions: 2 3/16” x 2 3/16”
141.165400 Valves, Orifices, and Manifolds
Clamp-on brass gas valve with straight outlet. Includes orifice.
- D-Value: 12 o'clock
- Stem diameter: 6mm
- Stem length: 1 3/4”
Includes orifice with #72
starter hole. Must be drilled to proper
drill size.
Replaces Kenmore factory part# P32C1B
Part Number: 3700C
Material: brass
Weight: 0.5
Dimensions: 4 15/16” x 2 1/8”
Neoprene valve gasket for clamp-on gas control valves. 19mm.
Part Number: 00019
Material: neoprene
Weight: 0.01
Dimensions: 0 1/2” x 0 1/4”
Brass orifice. 6mm x 3/4” cone shaped orifice with #64
drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper
drill size.
If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.
Part Number: 31400
Material: brass
Weight: 0.01
Dimensions: 0 3/4” x 0 5/16”
141.165400 Accessories
Part Number: 00185
Material: stainless
Weight: .3
20” Professional Extra Long Tong.
20” Stainless steel tong with red soft grip rubber inserts. Grip your food on the grill with ease. Manual lock saves on storage space.
Part Number: 40269
Material: stainless steel
Weight: 0.14
Deluxe 13” basting mop with hardwood handle and cotton mop head. Great for spreading BBQ sauces, marinades, and glazes on meat and poultry.
Part Number: 42055
Weight: 0.2
Dimensions: 13
Aluminum foil grilling trays. Package of three.
- Heavy duty aluminum foil
- Re-usable
- Great for grilling delicate foods like fish and veggies
Part Number: 50426
Weight: 0.4
Dimensions: 9” x 13”
Grill Mitt With Neoprene Palm. 16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most
Part Number: 90963
Weight: 0.2
|
Kenmore model 141.165400. If the BBQ grill part you are looking for is not listed above, make a note of the dimensions of your original part and try searching by part category. 02-Nov-26
|
We ship Kenmore BBQ parts worldwide
Back to Kenmore grill parts