Home > Kenmore Grill Models > Kenmore 141.173371
Use the dimensions of your old parts, preferably after removal, to compare to what we show below. Comparing dimensions is the best way to insure you get the right parts for your Kenmore grill.
Replacement grill parts for the Kenmore 141.173371
141.173371 Burners
Cast iron burner for Kenmore model 141.173371.
Replaces Kenmore factory part# P02001006C
Part Number: 29351
Material: cast iron
Weight: 2.2
Dimensions: 12 7/8” x 2 1/8”
141.173371 Cooking Grids
Cast iron
cooking grids (set of 2).
Porcelain enameled, glossy finish.
Replaces Kenmore factory part# P01615027E
Part Number: 68252
Material: gloss cast iron
Weight: 13.11
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 3/4″
Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.
- Made in USA

- Commercial grade 304 stainless steel
- .225” solid stainless rods
- Sold as a set of two (2).
Each panel measures:- Front-to-Back: 16 1/2”
- Side-to-Side: 11 1.4”
Total Side-to-Side: 22 1/2”NOTE: Some ProChef grills this part replaces used a wider single-piece grid.
Part Number: 53502-SS-X2
Material: stainless steel
Weight: 7.0
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 1/2″
Premium stainless steel cooking grid. Far superior to porcelain coated steel grids. Fits ProChef grills, may fit others.
- Made in USA

- Commercial grade 304 stainless steel
- .225” solid stainless rods
- Sold individually, 2 required.
Part Number: 53502-SS
Material: stainless steel
Weight: 3.50
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 11 1/4″
Premium quality stainless steel
cooking grids. SET OF TWO (2). Far superior to the porcelain coated steel grids it replaces.
- Made in USA

- 304 commercial grade stainless steel
- .225 diameter solid stainless rods
- Each panel measures 16 1/2” x 11 1/4”
- Overall dimensions: 16 1/2” x 22 1/2”
.
Part Number: CG-51SS-X2
Material: stainless steel
Weight: 7.0
Dimensions:
- Front-To-Back: 16 1/2″
- Side-To_Side: 22 1/2″
141.173371 Heat Plates
Stainless steel
heat plate/ Flame Tamer.
Made in USA
Replaces Kenmore factory part# P01705016E
Part Number: KENHP1
Material: stainless steel
Weight: 1.0
Dimensions:
- Front-To-Back: 13 1/8″
- Side-To_Side: 10 9/16″
SET OF THREE/3 PACK Stainless steel
heat plate/Flame Tamer. Made in USA

.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0154-X3
Material: stainless steel
Weight: 5.76
Dimensions:
- Front-To-Back: 13 3/16″
- Side-To_Side: 10 5/8″
Stainless steel
heat plate/Flame Tamer. Made in USA

.
NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.
Part Number: CLA-TS0154
Material: stainless steel
Weight: 1.92
Dimensions:
- Front-To-Back: 13 3/16″
- Side-To_Side: 10 5/8″
141.173371 Igniter Components
Igniter collector box, ceramic electrode with male
spade connector, and mounting plate.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02605013C
Part Number: 02618
Material: stainless steel
Weight: 0.3
Dimensions: 4
Battery powered push button igniter.
- Has four (4) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502024C
Part Number: IGEIB4-B
Weight: 0.3
Universal four-outlet battery powered push button ignitor.
- 1.5 volt
- Has four (4) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
- Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502024C
Part Number: 03340
Weight: 0.5
Battery powered push button igniter.
- Has two (2) spade type male connectors.
- Uses 1 AAA battery (not supplied)
- Requires 3/4” or 13/16” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502012C
Part Number: IGEIB2-B
Weight: 0.3
Small AA battery powered push button spark generator.
- 1.5 volt
- Has two (2) terminals (male spade connector)
- Uses a single AA battery (not included)
- 03610 and 03620 wires are commonly used with this igniter (not included)
- Requires 7/8” mounting hole
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502012C
Part Number: 03342
Weight: 0.3
Universal volt battery powered push button ignitor.
- 1.5 volt
- Has two (2) terminals (male spade connector)
- Uses a single AAA battery (not included)
- Requires 3/4” mounting hole
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Replaces Kenmore factory part# P02502252C
Part Number: 03320
Weight: 0.3
Push-button electronic igniter with two (2)
spade connectors. Black cap. 1 AAA battery (not included).
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG2006
Weight: 0.2
Push-button electronic igniter with four (4)
spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: TS-IG4010
Weight: 0.2
46” Wire with female
spade connectors and square plastic connectors.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: IG-30B
Weight: 0.1
Dimensions: 46
Ignition connection wire used to connect battery powered spark generators to electrodes. One 46” wire.
- Wire has female spade connector on one end and square plastic connector on the other
- Square plastice connector attaches to spark generator
- Female spade connector ataches to electrode
NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.
Part Number: 03610
Weight: 0.05
14” ground wire with female
spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.
For more information about ignition systems and components, please see article Ignition 101 in our help center.
Part Number: 03620
Weight: 0.1
141.173371 Knobs and Handles
Black control knob to fit Kenmore models for Kenmore model 141.173371.
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive Nov 6th.
Replaces Kenmore factory part# P03412331C
Part Number: 03430
Material: plastic
Weight: 0.2
Dimensions: 2 3/16” x 2 3/16”
141.173371 Valves, Orifices, and Manifolds
Clamp-on brass gas valve with straight outlet. Includes orifice.
- D-Value: 12 o'clock
- Stem diameter: 6mm
- Stem length: 1 3/4”
Includes orifice with #72
starter hole. Must be drilled to proper
drill size.
Replaces Kenmore factory part# Y0060094
Part Number: 3700C
Material: brass
Weight: 0.5
Dimensions: 4 15/16” x 2 1/8”
Neoprene valve gasket for clamp-on gas control valves. 19mm.
Part Number: 00019
Material: neoprene
Weight: 0.01
Dimensions: 0 1/2” x 0 1/4”
Brass orifice. 6mm x 3/4” cone shaped orifice with #64
drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper
drill size.
If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.
Part Number: 31400
Material: brass
Weight: 0.01
Dimensions: 0 3/4” x 0 5/16”
141.173371 Accessories
GrillPro Wood chips from genuine oak whiskey barrels.
- All natural wood smoke flavor
- Great for use in BBQ's or smokers.
- 170 cubic inches (2 lbs. approx) in resealable bag
Try with beef, burgers, pork, lamb, poultry, and fish.
Part Number: 00215
Weight: 2.0
Meat Claws. Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.
Part Number: 44070
Material: stainless steel
Weight: 0.5
Dimensions: 8 1/4
Stainless Steel Basting Set.
Measurements inside the stainless steel bowl for accurate sauce preparation. Includes silicone basting brush.
Part Number: 14913
Material: stailess steel
Weight: 0.5
Deluxe non-stick chicken and rib tumble basket. Attaches to rotisserie spit rod.
- Ideal for cooking pieces of meat or vegetables
- Self basting, easy to use
- Locks on spit rod with thumb screw (supplied)
- 6 1/2” x 10” long
Part Number: 24764
Weight: 1.1
Dimensions: 6 1/2” x 10”
Abrasive scrubbing brush. Ideal for cleaning porcelain grills.
Part Number: 71448
Weight: 0.2
|
Kenmore grill model 141.173371. Some parts not specific to a grill brand or model like regulators, posts, and heat indicators, which are listed in our repair parts section. 02-Nov-26
|
We ship Kenmore BBQ parts worldwide
Back to Kenmore grill parts